Search found 91 matches

by david
Fri Jan 11, 2019 12:25 pm
Forum: Software
Topic: cura crash 1/2 way through print - two computers
Replies: 2
Views: 282

Re: cura crash 1/2 way through print - two computers

Bart, I ran the stl file on my Mini 2 without incident. The file printed completely without any crash. perhaps the Rambo is causing an error? It is hard to tell.
by david
Tue Jun 13, 2017 4:14 pm
Forum: Hardware
Topic: Need help with bed heater
Replies: 7
Views: 1464

Re: Need help with bed heater

The bed thermistor is non replacable. ( not sure if that's a word) The entire heat bed will need to be replaced.
you can get a new one with PEI installed. Please make sue that the thermistor is the issue before you do, so that you don't have the same issue once you install the new one.
by david
Mon Jun 12, 2017 7:46 am
Forum: Hardware
Topic: Need help with bed heater
Replies: 7
Views: 1464

Re: Need help with bed heater

Hello gg, You must have an issue with your bed heater. The reading you should get when you set your meter to 200 ohms or less should read ~1.7ohm. The thermistor will read aprox. 100k ohms at room temp. If your bed heats up, then something is up with your meter. If the bed does not heat up, then it ...
by david
Mon Jun 05, 2017 4:23 pm
Forum: Hardware
Topic: tAZ 5 40 MM FAN VOLTAGE RATING
Replies: 2
Views: 1009

Re: tAZ 5 40 MM FAN VOLTAGE RATING

Hello Pete, The 40mm fan on the side of the hot end are 24volt fans. The fan on the heat sink of the hot end (front middle) is a 5 volt low flow 40mm fan. Please call the sales people during normal business hours and they will let you know about availability. 970-377-1111 Or you can contact https://...
by david
Wed May 31, 2017 6:52 am
Forum: LulzBot Mini
Topic: Calibrating Too High
Replies: 4
Views: 1132

Re: Calibrating Too High

Hello Paul, The M119, will just give you an end stop status report. You need to see if any of the end stops are triggered, once you enter it. If so it will indicate an issue there.(if your heat bed and tool head are in the middle of their travel) You may also want to enter a M851 command so that you...
by david
Mon May 29, 2017 12:09 pm
Forum: LulzBot Mini
Topic: Calibrating Too High
Replies: 4
Views: 1132

Re: Calibrating Too High

Hello, You may want to verify that you don't have a bad driver on the RAMBo. Please open Cura an go to machine and select your printer. Then please go to "install default firmware" and go through those steps. Then please load a model and then go to "expert" and select "quickprint". Then please go to...
by david
Mon May 29, 2017 12:03 pm
Forum: LulzBot TAZ
Topic: TAZ 6 switching back to original tool head
Replies: 4
Views: 1308

Re: TAZ 6 switching back to original tool head

Hello,

If you would like to give your serial number to support@lulzbot.com, we can tell you what your Esteps were that came with the printer.
I hope that may help.
by david
Mon May 22, 2017 3:21 pm
Forum: LulzBot Mini
Topic: New Printer Head Won't Work
Replies: 5
Views: 1266

Re: New Printer Head Won't Work

Hello, It sounds like when you were doing the "change tool head" step and flashing the firmware, that you selected the V1 hot end instead of the V2 hexagon. That would give you the error that you are seeing due to the max temp on the V1. Just go back to "machine" change tool head" and then make sure...
by david
Mon May 15, 2017 12:10 pm
Forum: LulzBot Mini
Topic: getting something strait, I cant make circles
Replies: 6
Views: 1114

Re: getting something strait, I cant make circles

You may want to verify that the pulley on the Y axis motor has the 1.27mm Allen set screw, tight against the flat of the motor shaft. Please make sure to use the flat of the Allen wrench as the ball end will strip the set screw.
Just in case the pulley is slipping on the shaft.
by david
Mon May 15, 2017 12:07 pm
Forum: LulzBot Mini
Topic: Bed levelling time and misalignment
Replies: 7
Views: 2077

Re: Bed levelling time and misalignment

Regarding the previous response. This would be for the Taz6. If there is an issue with the Mini (solid frame), then we would need to see a video at support@luzbot.com, to see if we could see what the cause is. Sorry if I was not clear on this!