Search found 197 matches

by gghouck
Fri Nov 09, 2018 4:05 pm
Forum: Hardware
Topic: How long should the bed PEI sheet last?
Replies: 2
Views: 390

Re: How long should the bed PEI sheet last?

I use pei on my Taz but use gluesticks on it and have seen no reason to replace it. Yes, I could just do without, but it's there and I just don't feel like removing it. If you use gluesticks there is little if any damage done to the pei in my experience.
by gghouck
Sun Nov 04, 2018 5:58 pm
Forum: LulzBot TAZ
Topic: Taz 6 out of level bed
Replies: 1
Views: 241

Re: Taz 6 out of level bed

What is the bed made of? glass beds are extremely flat so any warp you see will not be in that. Do you have a pei sheet that is lifting off the bed? did you level the bed with the corner adjustments? Are you sure the bed is actually warped and not just out of level?
by gghouck
Sun Nov 04, 2018 5:49 pm
Forum: LulzBot Mini
Topic: 1.75 mm extruder/hot end
Replies: 4
Views: 285

Re: 1.75 mm extruder/hot end

There was mention of people just sticking 1.75 filament in their Taz and it working as long as the appropriate changes were made in the slicing software.
by gghouck
Sun Nov 04, 2018 4:39 pm
Forum: LulzBot TAZ
Topic: Looking for a Extruder Extension Adapter v2c to v2b
Replies: 1
Views: 142

Looking for a Extruder Extension Adapter v2c to v2b

I'm looking for a couple of these adapters, but the can't find them on the site, or any other for that matter. Any ideas besides fabricating them?
by gghouck
Thu Aug 30, 2018 7:52 pm
Forum: Software
Topic: Why do I not get more layers in the slicer?
Replies: 5
Views: 491

Re: Why do I not get more layers in the slicer?

johnwmcc wrote:
Fri Aug 17, 2018 7:39 pm
What's S3D?
Likely short for "Simplify 3d"
by gghouck
Mon Aug 20, 2018 11:13 am
Forum: Hardware
Topic: Expanding Taz 4, need a little info
Replies: 6
Views: 373

Re: Expanding Taz 4, need a little info

Thank You
by gghouck
Sat Aug 18, 2018 8:21 am
Forum: Hardware
Topic: Expanding Taz 4, need a little info
Replies: 6
Views: 373

Re: Expanding Taz 4, need a little info

So, ALL my original questions still remain.
by gghouck
Sat Aug 18, 2018 7:48 am
Forum: Hardware
Topic: Expanding Taz 4, need a little info
Replies: 6
Views: 373

Re: Expanding Taz 4, need a little info

The stock bed takes 10 amps, I know this because my PSU has a built-in ammeter/volt meter and , so ~20 amps would heat the bigger bed at the same rate. Bigger wiring is the easy part since I am building the bed heater. So the questions still remain: If I go up to a 30 volt PSU, will that effect the ...
by gghouck
Fri Aug 17, 2018 9:01 am
Forum: Hardware
Topic: Expanding Taz 4, need a little info
Replies: 6
Views: 373

Expanding Taz 4, need a little info

My plan is to double the Y axis on my Taz 4. I'm getting ready to make the bed heater but need some help. So my plan is to make the heater1.6 ohms maybe less, meaning it will draw somewhere around 16 amps, which I believe is a bit much for the Ramboard (I don't recall which version of the board I ha...
by gghouck
Mon Apr 16, 2018 5:03 pm
Forum: Hardware
Topic: Need bed for Taz 4 expansion project
Replies: 2
Views: 535

Re: Need bed for Taz 4 expansion project

Thanks, Their quote for a 6mm thick 300mm x 600mm piece of borosilicate is $205.50 plus shipping.