Search found 63 matches

by geneb
Wed Dec 31, 2014 11:47 am
Forum: Hardware
Topic: TAZ hot end leaks...
Replies: 21
Views: 7289

Re: TAZ hot end leaks...

It's my understanding that some of the hot ends were equipped with a section of PTFE that's too short. If your leak is resulting in puddling on top of the heater block, you should contact support about it.

g.
by geneb
Wed Dec 10, 2014 3:06 pm
Forum: LulzBot TAZ
Topic: J-Head mount for the TAZ
Replies: 7
Views: 1335

Re: J-Head mount for the TAZ

Ahh, ok. Nah, that wouldn't solve the issue.

If I find the time over my vacation, I may spin a new rev of the mount that includes a filament guide tunnel and an extended face that dips below the X car on the TAZ. I've got to find a round tuit and fuel for the Givvadammatron first. :)

g.
by geneb
Wed Dec 10, 2014 8:17 am
Forum: LulzBot TAZ
Topic: J-Head mount for the TAZ
Replies: 7
Views: 1335

Re: J-Head mount for the TAZ

What is it?

g.
by geneb
Fri Dec 05, 2014 3:43 pm
Forum: LulzBot TAZ
Topic: J-Head mount for the TAZ
Replies: 7
Views: 1335

Re: J-Head mount for the TAZ

Unfortunately, it's fundamentally useless. :(

Because of how the Z end-stop switch & adjustment screw are positioned, the best I can do is 1/2" short of the bed surface with an Aluhotend. :(

The GOOD news is that the extruder feeds 1.75mm nicely!

*headdesk*

g.
by geneb
Fri Dec 05, 2014 8:29 am
Forum: LulzBot TAZ
Topic: J-Head mount for the TAZ
Replies: 7
Views: 1335

J-Head mount for the TAZ

After some thrashing about, I finally got this done.

http://repables.com/r/433

It's been tested to fit the Aluhotend and the hotends.com J-Head.

g.
by geneb
Sun Apr 27, 2014 8:07 am
Forum: Hardware
Topic: Auto bed probing and compensation with G29 Development
Replies: 127
Views: 68189

Re: Auto bed probing and compensation with G29 Development

Apparently, some jerk decided to delete the firmware off their github repo. *glares*

Here's the firmware I'm currently running and is the same used in the video I did:
http://www.geneb.org/TAZ/taz-autolevel-marlin.zip

g.
by geneb
Fri Jan 31, 2014 5:18 pm
Forum: Hardware
Topic: Auto bed probing and compensation with G29 Development
Replies: 127
Views: 68189

Re: Auto bed probing and compensation with G29 Development

https://github.com/larsbrubaker/Marlin/tree/Auto_Bed_Level I just copied and pasted it the first time from the first post of this topic. The ... in the link breaks it. Please see the actual link above. It is broken. Again, there's nothing wrong with the link. It's designed to be clicked, not copy/p...
by geneb
Fri Jan 31, 2014 8:57 am
Forum: Hardware
Topic: Auto bed probing and compensation with G29 Development
Replies: 127
Views: 68189

Re: Auto bed probing and compensation with G29 Development

The link works fine.

g.
by geneb
Sat Nov 30, 2013 9:29 pm
Forum: Hardware
Topic: Budaschnozzle fan duct...
Replies: 2
Views: 1174

Budaschnozzle fan duct...

Is there one available for the TAZ? I got four hours into a twelve hour print and the extruder jammed. :(

tnx.

g.