Search found 9 matches

by fluffywhitebunny
Mon Feb 18, 2019 11:53 am
Forum: Software
Topic: RAMBo fans running full blast after firmware update to 1.1.5.7
Replies: 3
Views: 537

Re: RAMBo fans running full blast after firmware update to 1.1.5.7

Well, I've waited 5 months now, updated the firmware again with the new cura using a mac, the update went fine, I can use cura with my mac but when I start warming up the hotend and bed the RAMBo fan runs way to fast, sounds like a jet engine now. Also using PC with Cura 3.2.32 and new firmware it d...
by fluffywhitebunny
Sat Sep 15, 2018 4:33 pm
Forum: Software
Topic: RAMBo fans running full blast after firmware update to 1.1.5.7
Replies: 3
Views: 537

Re: RAMBo fans running full blast after firmware update to 1.1.5.7

So i've cleared my cache's and have tried over and over to install (automatically) the new firmware...no luck, Cura say's it's upgrading firmware and it times out. I've manually installed the new firmware and printer looks good, shows the current version of firmware, but Cura will not find the print...
by fluffywhitebunny
Thu Apr 19, 2018 7:18 pm
Forum: Software
Topic: RAMBo fans running full blast after firmware update to 1.1.5.7
Replies: 3
Views: 537

RAMBo fans running full blast after firmware update to 1.1.5.7

Hi all, hopefully i'm not the only one with this issue: after updating to firmware 1.1.5.7 on my TAZ 5 my RAMBo (control unit) fans are running full blast. If I revert back to the old firmware the fans run at a "normal" speed. Has anyone noticed this? (kind of hard not to). What's the fix? Should I ...
by fluffywhitebunny
Mon May 18, 2015 2:48 pm
Forum: Hardware
Topic: Adding Laser to Taz 5..
Replies: 6
Views: 4218

Re: Adding Laser to Taz 5..

I'm very interested in this as well. I'll be watching this topic eagerly!
by fluffywhitebunny
Tue May 05, 2015 1:01 pm
Forum: Hardware
Topic: Clogged Hexagon Hotend
Replies: 6
Views: 4144

Re: Clogged Hexagon Hotend

Just an update, I heated the hotend up to ABS temp and using the 18mm and 7mm wrench it came off without a problem, just be careful the wrench and tip will be very hot. The threads are just like any other screw or bolt nothing to worry about at all, I was expecting very small hair sized threads, but...
by fluffywhitebunny
Mon May 04, 2015 4:18 pm
Forum: Hardware
Topic: Clogged Hexagon Hotend
Replies: 6
Views: 4144

Re: Clogged Hexagon Hotend

Awesome, thx for the tips, i'll heat it up and give it a try. The small wire sounds like a good idea, just need to find such wire, i'll just try the removal first. Thx.
by fluffywhitebunny
Sun May 03, 2015 11:57 am
Forum: Hardware
Topic: Clogged Hexagon Hotend
Replies: 6
Views: 4144

Clogged Hexagon Hotend

Anyone have any tips on cleaning out the Hexagon Hotend? I've read the tip in the manual for removing the hotend but from other users saying that the threads are near impossible to realign, and with my nozzle being "welded" (not actually) to the hotend, i'm a little leery of taking it off. I attempt...
by fluffywhitebunny
Sat Mar 14, 2015 9:34 pm
Forum: LulzBot TAZ
Topic: TAZ5 Hexagon Hotend Fan
Replies: 9
Views: 3342

Re: TAZ5 Hexagon Hotend Fan

Well I've contacted support, we'll see what they can suggest. Just to update though, I've tested the small hotend fan with a voltmeter, read a 4.95V on the meter, when the unit is up to temp. Found that at ambient temps I had no reading...so there must be some kind of temp sensor OR a bad power supp...
by fluffywhitebunny
Sat Mar 14, 2015 2:03 am
Forum: LulzBot TAZ
Topic: TAZ5 Hexagon Hotend Fan
Replies: 9
Views: 3342

TAZ5 Hexagon Hotend Fan

Just setup my Taz5 and plugged in the hotend, extruder and power cables for the two fans (one squirrel cage fan on the hotend fins, and the bigger fan for the Filament extrusion). Found that the two power cables for the fans can be swapped and at first I had them swapped (there was no mention in the...