Search found 74 matches

by doenute
Wed Jan 09, 2019 12:19 pm
Forum: Software
Topic: Cura 3.2.32 no bed heater settings
Replies: 1
Views: 256

Cura 3.2.32 no bed heater settings

Out of the blue Cura no longer displays the setting for initial or ongoing bed heat temperature--only the Removal temperature is available to change.

Let me guess....purge the Cache....
by doenute
Fri Dec 21, 2018 8:31 am
Forum: Software
Topic: Cura 3.2.32 Flow Rate wrong
Replies: 1
Views: 667

Cura 3.2.32 Flow Rate wrong

This version of cura does not work regarding flow rate on dual extrusion jobs

I selected a lower flow rate on layers 2+ and the flow rate was returned to 100%.

This was with Extruder 1
by doenute
Wed Dec 12, 2018 6:15 am
Forum: Software
Topic: Linear Advance with Dual Extrusion
Replies: 4
Views: 970

Re: Linear Advance with Dual Extrusion

It mainly works. There is a problem in Cura however for those that sometimes print with a single extruder when the dual extruder head is installed. If you print with extruder #2 ONLY then Cura will correctly insert the K factor entered in the "Hot End 2 start gcode" into the final gcode file for pri...
by doenute
Mon Dec 10, 2018 7:36 am
Forum: Software
Topic: Linear Advance with Dual Extrusion
Replies: 4
Views: 970

Re: Linear Advance with Dual Extrusion

Ok, I'll give it a try. I'm assuming it is OK to use a decimal place like K2.2?

Thanks
by doenute
Fri Dec 07, 2018 8:36 am
Forum: Software
Topic: Linear Advance with Dual Extrusion
Replies: 4
Views: 970

Linear Advance with Dual Extrusion

Can anyone confirm that I can use two different K values when dual printing--changing back and forth as each extruder is used?

Thanks!
by doenute
Fri Sep 14, 2018 8:44 am
Forum: Software
Topic: Cura 3.2.23 with flexydually v2 nozzle switch
Replies: 6
Views: 489

Re: Cura 3.2.23 with flexydually v2 nozzle switch

With all due respect, if I see "clear the cache" again I'm going to loose it.

Why is the software/installer not written to deal with this correctly to begin with?

This should not be the answer to every issue that comes up.
by doenute
Wed Sep 12, 2018 11:19 am
Forum: Software
Topic: Cura 3.2.23 with flexydually v2 nozzle switch
Replies: 6
Views: 489

Cura 3.2.23 with flexydually v2 nozzle switch

How do you control the point at which the standby nozzle begins to warm up? Right now going from nozzle one to zero is causing a pause in printing of about 30 seconds and leaving a large blob of Ninjaflex. Switching the other way has only a couple second delay.
by doenute
Thu Aug 30, 2018 10:52 am
Forum: Software
Topic: No Materials 3.2.23
Replies: 3
Views: 332

Re: No Materials 3.2.23

I had old 21.XX software installed. I uninstalled both older software, cleared all cache locations both old and new and re-installed new software.

Now, Extruder one only offers Matterhackers PLA and other extruder is still a red empty.
by doenute
Thu Aug 30, 2018 10:35 am
Forum: Software
Topic: No Materials 3.2.23
Replies: 3
Views: 332

Re: No Materials 3.2.23

No the option to discard current changes is greyed out.
by doenute
Thu Aug 30, 2018 9:04 am
Forum: Software
Topic: No Materials 3.2.23
Replies: 3
Views: 332

No Materials 3.2.23

After clearing cache etc on loading this new version and setting up a Lulzbot Taz 6 Flexistruderv2 there are no materials at all available for the second extruder(material field is red and says "none") The only material on extruder 1 that is available is Verbatim PLA. How can this be fixed to allow ...