Search found 12 matches

by Rookie
Fri Mar 15, 2019 9:14 pm
Forum: LulzBot TAZ
Topic: Source for 0.35 mm nozzle Taz 5
Replies: 4
Views: 237

Re: Source for 0.35 mm nozzle Taz 5

Here it is. I might read it wrong. These ones "might" fit http://www.reprapdiscount.com/hotends/70-hexagon-nozzle.html#/nozzle_size-0_4mm/filament-3mm The lulzbot hotend version has a longer heater block than the base reprap one. I don't know if that means the nozzles are different too. I don't have...
by Rookie
Fri Mar 15, 2019 8:52 pm
Forum: LulzBot TAZ
Topic: Source for 0.35 mm nozzle Taz 5
Replies: 4
Views: 237

Re: Source for 0.35 mm nozzle Taz 5

Thanks, that's what I was looking for.
I'll try to find the thread in my history. It didn't make sense to me either.
by Rookie
Fri Mar 15, 2019 4:46 pm
Forum: LulzBot TAZ
Topic: Source for 0.35 mm nozzle Taz 5
Replies: 4
Views: 237

Source for 0.35 mm nozzle Taz 5

Anyone know where I can buy a 0.35mm nozzle tip? From reading other threads the Taz 5 has a longer nozzle that goes deeper into the hot end so not any Hexagon nozzle will work. I contacted Lulzbot and they told me that they can sell me a new 0.5mm hotend assembly, but not just a nozzle. I would like...
by Rookie
Tue Jun 27, 2017 8:56 am
Forum: LulzBot TAZ
Topic: Suggestions on cleaning up print
Replies: 1
Views: 425

Suggestions on cleaning up print

I've had my Taz 5 for 2 yrs now. I just noticed the print quality deteriorated a little. Any suggestions? The 2 parts are left and right, 2 different files and printed ~4" away from each other on the print bed at different times. The dirty parts of the print appear to be at the same area of the part...
by Rookie
Thu Jun 15, 2017 7:39 pm
Forum: LulzBot TAZ
Topic: My TAZ 5 stops and no longer wants to print
Replies: 4
Views: 1279

Re: My TAZ 5 stops and no longer wants to print

Was you STL file clean? Did you run it through a mesh mixer and correct errors? That got me once.

viewtopic.php?f=36&t=2365&hilit=stops
by Rookie
Wed Jun 14, 2017 9:49 pm
Forum: LulzBot TAZ
Topic: Taz 5 to dual extruder V1 wire harness
Replies: 1
Views: 428

Taz 5 to dual extruder V1 wire harness

I have a Taz 5 and would like to hook up a V1 dual extruder. I need a 4 plug wire harness and the adapter for my existing wire harness. Anyone know where I can get them? I emailed support and like a few other things, "they are currently not in stock". "We should be making some up in the near future,...
by Rookie
Sat Jan 30, 2016 9:47 pm
Forum: Filament
Topic: NinjaFlex on PEI?
Replies: 7
Views: 2715

Re: NinjaFlex on PEI?

gghouck wrote:A coat or two of Aquanet helps with the release.
I'm with gghouck, a light mist of Aquanet before I print TPU or even some of my ABS's as a matter of fact. (Taz 5)
by Rookie
Tue Jul 07, 2015 10:09 pm
Forum: LulzBot TAZ
Topic: TAZ 5 Stops
Replies: 13
Views: 2458

Re: TAZ 5 Stops

Downloaded Netfabb Basic and watched 10 mins of youtube. Pretty simple.
Thanks once again.
by Rookie
Tue Jul 07, 2015 6:18 pm
Forum: LulzBot TAZ
Topic: TAZ 5 Stops
Replies: 13
Views: 2458

Re: TAZ 5 Stops

Thanks everyone for the help. I'm pretty new to this 3D printing stuff and kind of ignorant on the slicing and I guess the checking of the STL file. I have just been plugging the STL files into Cura and changing a couple of settings on my printer. So far all has worked out well until this. I do noti...
by Rookie
Tue Jul 07, 2015 6:55 am
Forum: LulzBot TAZ
Topic: TAZ 5 Stops
Replies: 13
Views: 2458

Re: TAZ 5 Stops

Hope this works. I'm sending from my phone.