Search found 23 matches

by greg50
Sun Sep 22, 2019 10:14 am
Forum: Hardware
Topic: Dual V2
Replies: 3
Views: 470

Re: Dual V2

A little late... hope you found the assembly directions for the Flexy-Dually V2 which should be pretty close if not the same directions: https://ohai.lulzbot.com/project/lulzbot-taz-flexy-dually-v2-extruder/hot-end-tool-head-assembly/ Thanks, Actually not too late. It took me 3 weeks to get the par...
by greg50
Sun Sep 22, 2019 10:10 am
Forum: Hardware
Topic: Dual V2 now a boat anchor
Replies: 3
Views: 182

Re: Dual V2 now a boat anchor

E3D did have them. Took like 3 weeks to get here.
by greg50
Tue Aug 27, 2019 6:02 pm
Forum: Hardware
Topic: Dual V2 now a boat anchor
Replies: 3
Views: 182

Dual V2 now a boat anchor

Well I am being told by support that I can't buy a thermistor nor a hotend anymore. Does this mean my Dual V2 just became a boat anchor? No one makes an equivalent termistor? Is there new hotends I can use other than the AO's? I just bought this about 2 years ago. Seems like a $500 item should not b...
by greg50
Tue Aug 27, 2019 1:50 pm
Forum: Hardware
Topic: Dual V2
Replies: 3
Views: 470

Re: Dual V2

Were they removed on purpose?
by greg50
Sun Aug 25, 2019 1:01 pm
Forum: Hardware
Topic: Dual V2
Replies: 3
Views: 470

Dual V2

I can't find the assembly instructions for the Dual V2. I have one that one of the screw pad for the tiny fans on the Javilin Flex Plate crack and the screw fell out. I printed a new one and now need to reassemble. But there instructions seem to no longer be on the OHAI site.
by greg50
Sat Aug 24, 2019 2:17 am
Forum: Hardware
Topic: Dual V3 bed alignment
Replies: 3
Views: 384

Dual V3 bed alignment

I have a taz 5 and recently purchased a dual V3 toolhead. After trying several mulitcolor prints; all of which look horrible, I decided to swap and print my primary from extruder2 and secondary from extruder1. When I did this the printer made spaghetti. Then i noticed that the right hand (extruder2 ...
by greg50
Fri Aug 16, 2019 12:19 am
Forum: Cura LulzBot Edition: Development & Testing
Topic: Dual Extruder Prime Tower Issue
Replies: 14
Views: 334

Re: Dual Extruder Prime Tower Issue

I used S3D with my previous printer, so since it was paid for it continued on to my Taz5. Ok, this is a little off topic, but... S3D=Simplify 3d correct? If so is it worth it. I've been thinking about buying it but there is no trial. Also I always liked that lulzbot had print profiles they had supp...
by greg50
Fri Aug 16, 2019 12:00 am
Forum: Cura LulzBot Edition: Development & Testing
Topic: Dual Extruder Prime Tower Issue
Replies: 14
Views: 334

Re: Dual Extruder Prime Tower Issue

Ok, I downloaded the cones and the prime tower did the exact same thing. Outer (Red) wall of tower is printed every layer all the way up even if that layer had no Red. Inner (White) wall only printed if white was on that layer. However, when playing around I accidentally clicked on support. Telling ...
by greg50
Thu Aug 15, 2019 11:39 pm
Forum: Cura LulzBot Edition: Development & Testing
Topic: Dual Extruder Prime Tower Issue
Replies: 14
Views: 334

Re: Dual Extruder Prime Tower Issue

Guys, Take 5 mins and load the STL's, run the layers up. Use any two color print. You will find that it does NOT print one color on top of the other on the prime tower. It creates two walls. The ooze shield does appear to alternate colors on the same layer, but not the prime tower. Work the layer sl...
by greg50
Thu Aug 15, 2019 5:02 pm
Forum: Cura LulzBot Edition: Development & Testing
Topic: Dual Extruder Prime Tower Issue
Replies: 14
Views: 334

Re: Dual Extruder Prime Tower Issue

Guys Something is wrong indeed. If the layers prime on top of each other they would eventually get taller than the print due both colors being on same layer and the tower height effectively doubling on that layer. They definitely print as two walls on the prime tower and as far as i can remember, al...