Search found 9 matches

by KW-printer
Thu Jan 28, 2016 3:35 pm
Forum: Software
Topic: Updating firmware on AO-100
Replies: 5
Views: 1186

Re: Updating firmware on AO-100

I tried opening the file Marlin.h in the Arduino IDE and it opened and everything looked OK. So I went ahead and uploaded it to the printer (after saying a Hail Mary). Everthing seems to have gone OK. I haven't printed anything yet but have moved stuff aroung using pronterface and everything seems o...
by KW-printer
Thu Jan 28, 2016 9:49 am
Forum: Software
Topic: Updating firmware on AO-100
Replies: 5
Views: 1186

Re: Updating firmware on AO-100

Hi piercet. I am not having any problems extracting the archive. But there is no file called "Marlin.ino" in there. The contents of the archive for the AO-100 firmware are shown here . There is no "Marlin.ino". There is a "Marlin.ino" in the archive for the AO-101 firmware (contents shown here ). Ma...
by KW-printer
Wed Jan 27, 2016 7:08 pm
Forum: Software
Topic: Updating firmware on AO-100
Replies: 5
Views: 1186

Updating firmware on AO-100

I am attempting to update the firmware on my AO-100. I am using the instructions I found here . Everything's going fine until I get to the step "Open the Arduino IDE and open Marlin.ino". The problem is there is no file called "Marlin.ino" in the firmware archive (Marlin.tar.bz2) downloaded for the ...
by KW-printer
Sun Sep 20, 2015 12:21 pm
Forum: AO-101 & AO-100
Topic: How to disconnect hot end from wiring harness?
Replies: 10
Views: 4129

Re: How to disconnect hot end from wiring harness?

I've finished this project now and just want to leave a few notes in case anyone else looking for help finds this thread. After the last post I made I took a closer look at what Lulzbot sent me with Budaschnozzle 2.0c. It turns out they had already sent me everything I need to make the hot end disco...
by KW-printer
Sat Sep 05, 2015 4:44 pm
Forum: AO-101 & AO-100
Topic: How to disconnect hot end from wiring harness?
Replies: 10
Views: 4129

Re: How to disconnect hot end from wiring harness?

I tried one of the female sockets I ordered in on one of the male pins in the budaschnozzle connector and it feels loose. Much looser than if I try the female socket on one of the male pins I ordered in. I think I'm just gonna order in a dozen each of the pins listed on the budaschnozzle spec page a...
by KW-printer
Sat Sep 05, 2015 3:17 pm
Forum: AO-101 & AO-100
Topic: How to disconnect hot end from wiring harness?
Replies: 10
Views: 4129

Re: How to disconnect hot end from wiring harness?

Hi piercet, I have a question if you are about. I have ordered in the parts you suggested in your post above and am preparing to do the changeover. The budaschnozzle 2.0c came with a 4 pin connector already attached. It says on the budaschnozzle 2.0c spec page that the male connector pins are 24-30 ...
by KW-printer
Sun Aug 23, 2015 5:47 pm
Forum: AO-101 & AO-100
Topic: How to disconnect hot end from wiring harness?
Replies: 10
Views: 4129

Re: How to disconnect hot end from wiring harness?

piercet, do you think this tool is good enough to do the crimping? Or would you recommend something higher end?
Image
by KW-printer
Sat Aug 22, 2015 2:16 pm
Forum: AO-101 & AO-100
Topic: How to disconnect hot end from wiring harness?
Replies: 10
Views: 4129

Re: How to disconnect hot end from wiring harness?

Thanks piercet, that is much appreciated.
Is this the 2 pin connector block you mentioned?:
Image
by KW-printer
Sat Aug 22, 2015 12:08 pm
Forum: AO-101 & AO-100
Topic: How to disconnect hot end from wiring harness?
Replies: 10
Views: 4129

How to disconnect hot end from wiring harness?

There are a number of instrucionals here in the forum that include the step "disconnect hot end from wiring harness" (see here). But I can't figure out how to do it on my AO-100. Do I have to cut wires? Or is there something that can be disconnected and reconnected? Can anyone offer any help?