Search found 35 matches

by cabbage_breath
Tue Apr 22, 2014 3:22 pm
Forum: 3D Scanner Software
Topic: LulzBot 3D Scanner
Replies: 35
Views: 19744

Re: LulzBot 3D Scanner

Did this project lose funding?
by cabbage_breath
Wed Feb 05, 2014 6:52 am
Forum: LulzBot TAZ
Topic: Bed Corners for 12"x12" Bed
Replies: 0
Views: 1133

Bed Corners for 12"x12" Bed

I altered the original 1.0 Bed Corner (because I liked the original, large design) to accommodate a 12" x 12" heated bed. It also has tabs on the bottom for keeping a stripboard heater (like this http://www.thingiverse.com/make:54040 ) off the aluminum bed plate. Thingiverse entry: http://www.thingi...
by cabbage_breath
Mon Jan 27, 2014 8:25 pm
Forum: 3D Scanner Software
Topic: LulzBot 3D Scanner
Replies: 35
Views: 19744

Re: LulzBot 3D Scanner

Step 2, B: "in reality opencv might be useful here"

Could you please explain what that means? What is opencv and how will it be implemented?

Thanks
by cabbage_breath
Tue Jan 21, 2014 6:50 pm
Forum: 3D Scanner Software
Topic: LulzBot 3D Scanner
Replies: 35
Views: 19744

Re: LulzBot 3D Scanner

Will this project have a repository in the devel.lulzbot site?

I would be interested in building one if the cost of prototyping isn't too prohibitive.
by cabbage_breath
Wed Jan 15, 2014 1:22 pm
Forum: Hardware
Topic: Electrical stuff question
Replies: 17
Views: 8121

Re: Electrical stuff question

Word.

Looking forward to a picture :)
by cabbage_breath
Wed Jan 15, 2014 11:55 am
Forum: Hardware
Topic: Electrical stuff question
Replies: 17
Views: 8121

Re: Electrical stuff question

Ok these things are just plug n play. You could plug both into the same 12v source but make sure you do it in parallel, not series. If you decide to use the port on the controller board then you would be able to switch it remotely which may be more attractive to you than a physical switch. Depends o...
by cabbage_breath
Wed Jan 15, 2014 8:53 am
Forum: Hardware
Topic: Electrical stuff question
Replies: 17
Views: 8121

Re: Electrical stuff question

just reread the OP. If both things are rated for 12v then you will need to connect them in parallel (lmk if you need clarification there). Once again I can give you a good answer if you send me to their source. So that would look something like this: Wire going from the positive end of the PSU to a ...
by cabbage_breath
Wed Jan 15, 2014 8:34 am
Forum: Hardware
Topic: Electrical stuff question
Replies: 17
Views: 8121

Re: Electrical stuff question

First question: The reason people call for a resistor is because you need to limit the current going into an LED to about 20mA (varies between colors). If you have a strip of LEDs then you need to know how much voltage each LED "uses" when operating. I am assuming you are using a 12v psu. Let's just...
by cabbage_breath
Tue Jan 14, 2014 1:01 am
Forum: LulzBot TAZ
Topic: TAZ hardware list
Replies: 4
Views: 6883

Re: TAZ hardware list

you can use my BOM from the 1.0 if this is for a DIY build. https://docs.google.com/spreadsheet/ccc ... ring#gid=6

It should be quite close to everything for a 3.0 replication as well
by cabbage_breath
Tue Jan 14, 2014 12:57 am
Forum: LulzBot TAZ
Topic: Z axis Centimeter on Home?
Replies: 3
Views: 1109

Re: Z axis Centimeter on Home?

I think it means that if you screw in the Z Adjustment Scew 10mm (20 turns) and then press "HOME" then the nozzle tip should be 10mm (+an teeny bit for proper nozzle height but perhaps that comes later in the guide) above the bed. If the tip to bed distance is greater or less than 10mm then you know...