Search found 49 matches

by bladerunner
Mon Oct 08, 2018 7:54 am
Forum: Software
Topic: Issues with prints pausing after Cura and firmware update
Replies: 20
Views: 2383

Re: Issues with prints pausing after Cura and firmware update

Thanks for the update. I had also reverted back to the older version of Cura and have not had an issue since.

I'm hoping they get that fixed because eventually I'd like to be able to use the new software.

~Michael
by bladerunner
Tue Oct 02, 2018 12:40 am
Forum: Software
Topic: Issues with prints pausing after Cura and firmware update
Replies: 20
Views: 2383

Re: Issues with prints pausing after Cura and firmware update

I printed the Rockopus successfully as well, but tried printing something else directly after that and it paused again mid-print.
by bladerunner
Mon Oct 01, 2018 7:43 pm
Forum: Software
Topic: Issues with prints pausing after Cura and firmware update
Replies: 20
Views: 2383

Re: Issues with prints pausing after Cura and firmware update

I upgraded Cura to the latest version (3.2.27), updated firmware, and continuing to have the same issue. I made sure to clear out the cache before upgrading.

Mine doesn't do it every time, but most times.

Any response from Lulzbot?
by bladerunner
Sun Sep 30, 2018 7:54 pm
Forum: Software
Topic: Issues with prints pausing after Cura and firmware update
Replies: 20
Views: 2383

Re: Issues with prints pausing after Cura and firmware update

Here's a an example....

These 2 prints were printed back to back. The one on the right was orientated left-to-right on the print bed and the print on the left was rotated 90 degrees and re-printed. As you can see, both stopped at different heights during the print.


`Michael
by bladerunner
Sun Sep 30, 2018 6:41 pm
Forum: Software
Topic: Issues with prints pausing after Cura and firmware update
Replies: 20
Views: 2383

Issues with prints pausing after Cura and firmware update

Hey gang, I have a Lulzbot Mini 1 and I recently upgraded my Cura software to the latest version (3.2.23) and the latest firmware and since then, randomly my prints will just pause in the middle of a print job. The print-head and the bed will still be at print temperature when it pauses so when I co...
by bladerunner
Thu Feb 09, 2017 3:51 pm
Forum: LulzBot Mini
Topic: PEI Film Woes
Replies: 17
Views: 3367

Re: PEI Film Woes

No luck with warranty replacement here. I talked to customer support and emailed them pictures and they said it wasn't warranty item, because the bubbles were caused by improper removal of parts. I always made sure to remove the parts at the recommended temperatures. Oh well, I bought a new one that...
by bladerunner
Thu Feb 09, 2017 3:44 pm
Forum: LulzBot Mini
Topic: Calibration Cube Usege?
Replies: 2
Views: 776

Calibration Cube Usege?

Hi, I just printed a 25x25x25mm calibration cube with a wall thickness of 3mm. When checking with my calipers I'm getting 25.23mm wide, 25.22mm deep, 25.02mm tall and 3.25mm wall thickness. Question are, what is an acceptable tolerance? Are these acceptable tolerances? If not, what do I need to do t...
by bladerunner
Sat Jan 28, 2017 5:42 pm
Forum: LulzBot Mini
Topic: PEI Film Woes
Replies: 17
Views: 3367

Re: PEI Film Woes

Scott,

That's very useful information, thank you. I started with HIPS and ABS as well, and found after much frustration that PETG was the way to go. I'll give warranty a call and see what they have say.

Thanks again!
by bladerunner
Sat Jan 28, 2017 2:29 pm
Forum: LulzBot Mini
Topic: PEI Film Woes
Replies: 17
Views: 3367

PEI Film Woes

I used my Lulzbot Mini for about a month and then I started having issues with prints not sticking to the bed. After speaking with customer support they recommended using 10% IPA/Water mix and a high grit sandpaper to lightly roughen up the surface. After doing this, the prints stuck great for awhil...
by bladerunner
Thu Apr 14, 2016 1:26 pm
Forum: Filament
Topic: PETG Dishwasher Safe?
Replies: 4
Views: 3902

PETG Dishwasher Safe?

Anyone know if PETG is dishwasher safe?

Thanks!