Search found 94 matches

by JoeBowler300
Wed Sep 11, 2019 1:09 pm
Forum: LulzBot TAZ
Topic: Duel V3 Heat Creep Fix
Replies: 4
Views: 117

Re: Duel V3 Heat Creep Fix

http://download.lulzbot.com/TAZ/accesso ... /heatsink/

Now you gotta send me the final product for “testing” purposes. :D
by JoeBowler300
Wed Sep 11, 2019 12:55 pm
Forum: LulzBot Mini
Topic: Mini Z motor grinding noise and binding
Replies: 10
Views: 670

Re: Mini Z motor grinding noise and binding

I had this exact symptom on my TAZ 6. This quick re-alignment/ synch procedure fixed me right up! Thank you for sharing this tip!
by JoeBowler300
Sun Sep 08, 2019 8:36 pm
Forum: LulzBot TAZ
Topic: Duel V3 Heat Creep Fix
Replies: 4
Views: 117

Re: Duel V3 Heat Creep Fix

This is the best solution to the heat creep problem on the dual v3 and I’ve tried all the other solutions with little to no improvement. With this setup I was able to print through a whole role of PLA within a week and printing back to back to back! Previously I was practically guaranteed a print fa...
by JoeBowler300
Wed Aug 14, 2019 12:08 am
Forum: LulzBot TAZ
Topic: [Dual Extruder v3] Filament Stops Feeding, Ruins Print, Can't get out Easily
Replies: 17
Views: 881

Re: [Dual Extruder v3] Filament Stops Feeding, Ruins Print, Can't get out Easily

I can confirm that the 1.5 to 2 hour mark is about the time my PLA prints would fail on the Dual Extruder v3. I doubt turning up your speed from 40mm/s will make any real difference, I use the default profile's speed setting of 60mm/s and still experience failures around the same time you do. Both e...
by JoeBowler300
Wed Aug 07, 2019 7:45 am
Forum: Hardware
Topic: E3D-v6 changing filament is an issue
Replies: 9
Views: 583

Re: E3D-v6 changing filament is an issue

If you pull it out when its hot and melted there's a good chance the filament will cling to the components in its path like hot gum on the ground. Then that filament will cool and cause blockage with no good way to warm it up and soften it. Not a literal cold pull at room temp but rather a warm cold...
by JoeBowler300
Wed Aug 07, 2019 7:37 am
Forum: LulzBot TAZ
Topic: [Dual Extruder v3] Filament Stops Feeding, Ruins Print, Can't get out Easily
Replies: 17
Views: 881

Re: [Dual Extruder v3] Filament Stops Feeding, Ruins Print, Can't get out Easily

Very possible! Definitely with PLA. The picture you uploaded looks like nGen filament correct? How long into the print? What's your printing speed? Are you printing with a 2nd filament in the other extruder? If not I suggest getting the Aerostruder print head with a silicone soc for single filament ...
by JoeBowler300
Wed Aug 07, 2019 1:24 am
Forum: Software
Topic: Cura 3.6.13 consistent print failure due to E-
Replies: 4
Views: 146

Re: Cura 3.6.13 consistent print failure due to E-

You say TWICE but you don't show all the detail. Here's more of the section that you left out: T0 ; select this extruder first M82 ; set extruder to absolute mode G92 E0 ; set extruder to zero G1 E-15 F100 ; suck up XXmm of filament T1 ; switch extruders M82 ; set extruder to absolute mode G92 E0 ; ...
by JoeBowler300
Wed Aug 07, 2019 12:42 am
Forum: Hardware
Topic: How to replace aerostruder Thermister
Replies: 3
Views: 404

Re: How to replace aerostruder Thermister

1.) A soldering iron can melt the point where the plastic is on the heater block and then use some tool to transfer the melted plastic too. 2.) You can heat up the tool’s point(screw driver or hex key), then insert it through the plastic and unscrew. 3.) replace the heater block along with the therm...
by JoeBowler300
Wed Aug 07, 2019 12:29 am
Forum: Hardware
Topic: E3D-v6 changing filament is an issue
Replies: 9
Views: 583

Re: E3D-v6 changing filament is an issue

You need to extrude 10mm or so at the printing temperature then drop it about 20 C (from the lower temp of the filament’s printing temperature range) and then cold pull out the filament.