Search found 76 matches

by JoeBowler300
Thu Jun 20, 2019 8:48 pm
Forum: Hardware
Topic: Taz Pro Vs Raise3d Pro 2 vs Ultimaker E /S5
Replies: 2
Views: 65

Re: Taz Pro Vs Raise3d Pro 2 vs Ultimaker E /S5

Markforged 3D printers may be a good candidate too.
by JoeBowler300
Wed Jun 19, 2019 9:29 pm
Forum: LulzBot TAZ
Topic: Lulzbot Taz 6: Different Nozzles
Replies: 2
Views: 58

Re: Lulzbot Taz 6: Different Nozzles

The ruby nozzle won’t work on the TAZ 6 because the auto leveling feature is sensed through the nozzle via capacitance I think. Never put anything conductive on the nozzle (i.e. wire brush, water, wrench) on the nozzle while the printer is on else you’ll probably blow the micro fuse and have to deal...
by JoeBowler300
Thu Jun 13, 2019 7:41 am
Forum: LulzBot TAZ
Topic: [Dual Extruder v3] Disassembly of extruders from heat break
Replies: 1
Views: 47

Re: [Dual Extruder v3] Disassembly of extruders from heat break

At this point you could probably separate the heat break from the heatsink by unscrewing those very tiny allen head screws, use the smallest Allen wrench from the kit that came with your Taz 6. Once separated you can use a heat gun or flame to melt off the plastic.
by JoeBowler300
Sat Jun 08, 2019 12:31 pm
Forum: Filament
Topic: Collapsing Katana Test Print Issues
Replies: 3
Views: 144

Re: Collapsing Katana Test Print Issues

Well I have to admit, that sword looks pretty cool! It looks to like you’re over extruding or over heating a little bit. I have a few suggestions. Maybe dial down your first layer height to the same height as the rest of the print. Change the flow rate to 90% because plastic expands, I get better di...
by JoeBowler300
Thu Jun 06, 2019 5:57 pm
Forum: LulzBot TAZ
Topic: [Dual Extruder v3] Filament Stops Feeding, Ruins Print, Can't get out Easily
Replies: 6
Views: 159

Re: [Dual Extruder v3] Filament Stops Feeding, Ruins Print, Can't get out Easily

Heat creep is horrendous on the dual v3 and PLA. Recently for the first time I’ve had to take apart the head to get the filament out. But first try this if you can still grab onto the filament from the top where it feeds. Heat up the Extruder to about 180, put a card over the front fan that’s attach...
by JoeBowler300
Sun Jun 02, 2019 5:55 pm
Forum: Hardware
Topic: Newbie needs help
Replies: 6
Views: 187

Re: Newbie needs help

What size is you nozzle? Is it the standard .5 mm or something larger? It still looks to me like a lot of filament is still coming out, as if you're using a large nozzle diameter or a worn out nozzle. Especially if the nozzle is brass, brass is one of the softest metals used for nozzles. You said yo...
by JoeBowler300
Sun May 26, 2019 11:23 pm
Forum: Filament
Topic: Trouble Removing ABS Print
Replies: 5
Views: 192

Re: Trouble Removing ABS Print

Ahhh yes, I apologize! I was thinking of the ninjaflex filament, you’ll want to use a glue stick when printing with that filament.
by JoeBowler300
Sun May 26, 2019 12:00 am
Forum: Filament
Topic: Trouble Removing ABS Print
Replies: 5
Views: 192

Re: Trouble Removing ABS Print

Gotta use a glue stick as a release agent for ABS. When stuck try spraying with a mixture of water and alcohol.
by JoeBowler300
Sat May 25, 2019 10:38 am
Forum: Hardware
Topic: Newbie needs help
Replies: 6
Views: 187

Re: Newbie needs help

Have you tried the bed leveling procedure found in this post? https://forum.lulzbot.com/viewtopic.php?f=36&t=7904 I highly recommend it! It also looks like you may be over extruding. Check your e-steps. In fact, find the tests the help you calibrate your e-steps. If you send 100mm of filament throug...
by JoeBowler300
Fri May 24, 2019 6:38 pm
Forum: Hardware
Topic: Taz 6, moving filament reel up top, use filament guide tube or no?
Replies: 5
Views: 169

Re: Taz 6, moving filament reel up top, use filament guide tube or no?

I found without the tube guide the filament will become a bit brittle if you don't print for a while ( a week or 2) and may snap in half within a few moves possibly leaving you with a terrible jam. Other than that, I agree I don't think it's really needed. Perhaps it also helps keep it a little bit ...