Search found 31 matches

by InfiniteGinger
Sun Mar 24, 2019 11:05 pm
Forum: Hardware
Topic: Einsy Retro on the Taz 6
Replies: 10
Views: 1593

Re: Einsy Retro on the Taz 6

Following. I’d like to know too
by InfiniteGinger
Fri Mar 15, 2019 9:28 am
Forum: Hardware
Topic: Looking for Socks
Replies: 1
Views: 477

Looking for Socks

Have a silicone sock for my Aerostruder without it my toolhead goes into thermal runaway at temps ~215...Wondering if anyone has found socks that fit the V3 Dual Aero?
by InfiniteGinger
Mon Mar 04, 2019 4:37 pm
Forum: Software
Topic: OctoPrint disconnects after printer asks to re-Wipe
Replies: 5
Views: 748

OctoPrint disconnects after printer asks to re-Wipe

Since updating to latest Marlin firmware 1.1.9.34 my OctoPrint disconnects if the printer reports it needs to rewipe before printing. Octoprint will report a firmware error and disconnect. the printer will keep running the auto level sequence and after rewiping will touch all four corners and wait f...
by InfiniteGinger
Tue Jun 26, 2018 9:06 am
Forum: LulzBot TAZ
Topic: Aerostruder Z-offset
Replies: 1
Views: 394

Aerostruder Z-offset

Forgiveness if this has already been addressed, a quick search of the forums didn't appear to yield the answer. For those of you with the L.B. Aerostruder, did you have to significantly alter your Z-height offset? Mine was printing way to close to the bed at -1.35, like WAY to close. The bottoms on ...
by InfiniteGinger
Mon Mar 26, 2018 12:03 pm
Forum: Filament
Topic: Ninja flex artifacts aerostruder
Replies: 4
Views: 859

Re: Ninja flex artifacts aerostruder

ty I'll give this a try tonight too. Dialing back the flow didn't help.
by InfiniteGinger
Tue Mar 06, 2018 12:39 am
Forum: Software
Topic: Octoprint communication issues
Replies: 11
Views: 18723

Re: Octoprint communication issues

Changing the baud to fixed 250000 (as suggested above) will eliminate some connection time since Octoprint won't have to trial/error to find it. But the problem you are having (the timeout) doesn't appear related to baud rate. Octoprint found the correct baud rate (250000), and was operating at tha...
by InfiniteGinger
Tue Mar 06, 2018 12:27 am
Forum: Software
Topic: Octoprint communication issues
Replies: 11
Views: 18723

Re: Octoprint communication issues

Change Octoprint's baud rate to fixed at 250000. set fixed rate to 250000...new error Unhandled communication error There was an unhandled error while talking to the printer. Due to that OctoPrint disconnected. Error: EEPROM CRC mismatch - (stored) 8643 != 55636 (calculated)! for some reason, conti...
by InfiniteGinger
Sun Mar 04, 2018 2:42 pm
Forum: Software
Topic: Octoprint communication issues
Replies: 11
Views: 18723

Octoprint communication issues

Taz 6 V3 Dual toolhead. Running latest firmware and Cura. Historically, I could connect to Octoprint\RP3 via Cura and start prints from within Cura with the wireless... Since installing the V3 Dual, the connection isn't reliable. Every print job the tool head just stops. If i click the "fake acknowl...
by InfiniteGinger
Wed Feb 28, 2018 10:52 pm
Forum: Filament
Topic: Ninja flex artifacts aerostruder
Replies: 4
Views: 859

Re: Ninja flex artifacts aerostruder

awesome ty
by InfiniteGinger
Fri Feb 23, 2018 8:50 am
Forum: Filament
Topic: Ninja flex artifacts aerostruder
Replies: 4
Views: 859

Ninja flex artifacts aerostruder

So far really liking the Aerostruder. Printed this Rocktopus last night. Lots of artifacts. Didn’t see any estep calibration in the instructions or a sticker on the tool head.

What am I missing here? Image