Search found 509 matches

by Brent.I
Thu Oct 10, 2019 2:59 pm
Forum: LulzBot TAZ
Topic: RAMBo v1.3 vs v1.4 [TAZ6]
Replies: 1
Views: 189

Re: RAMBo v1.3 vs v1.4 [TAZ6]

You can read up on the full stats of the board here: https://ultimachine.com/products/rambo-1-4 From the article however: RAMBo v1.4 - The major difference over the previous version is the integrated LCD connector for Smart LCD Controllers. The EXT2 and SPI headers were re-arranged to remove the nee...
by Brent.I
Tue Oct 08, 2019 9:38 am
Forum: Hardware
Topic: Marlin2 Firmware for TAZ6 and older???
Replies: 4
Views: 667

Re: Marlin2 Firmware for TAZ6 and older???

166 versions so far. We just hit 170 today :D One of the big reasons we have not been able to release a "stable" version of Marlin 2.0 for our older generations of printers is due to the fact upstream marlin 2.0 is still considered "experimental." You can see their latest stable release notes here:...
by Brent.I
Fri Sep 27, 2019 7:41 am
Forum: Software
Topic: Flow set to 115%?
Replies: 2
Views: 261

Re: Flow set to 115%?

when I switch to the Taz, flow is bumped up to 115%. On our older generations of Flextystruder tool heads we needed to set a higher flow rate in order to print flexible materials properly. In an attempt to avoid adjusting esteps when swapping between we first experimented with adjusting flow rate. ...
by Brent.I
Mon Sep 23, 2019 12:30 pm
Forum: LulzBot TAZ
Topic: Taz 6 Motion Controlls
Replies: 5
Views: 466

Re: Taz 6 Motion Controlls

B-Hep-Spring wrote:
Mon Sep 23, 2019 12:19 pm
although some are not given X Y Z ect but thank you..
No problem. In general when they are not listed (for example max acceleration) it will always be listed in this order: X, Y, Z, E1, E2
by Brent.I
Mon Sep 23, 2019 12:16 pm
Forum: LulzBot TAZ
Topic: Taz 6 Motion Controlls
Replies: 5
Views: 466

Re: Taz 6 Motion Controlls

B-Hep-Spring wrote:
Mon Sep 23, 2019 12:10 pm
that would be just too easy.
The config file is exactly what you are looking for. Open it in a word editor, and search for you desired setting. (In this case Max) You will want to be sure to select the proper tool head and printer combination that you are using to get accurate data.
by Brent.I
Mon Sep 23, 2019 8:00 am
Forum: LulzBot TAZ
Topic: Thermal Error E1
Replies: 5
Views: 329

Re: Thermal Error E1

It sounds like you could have a failing heater cartridge. The error message you are receiving is thrown when the hot end is attempting to heat, but it is not registering a change in temperature. You can measure the resistance of the heater cartridge to verify, it should be ~20ohms at room temperatur...
by Brent.I
Mon Sep 23, 2019 7:57 am
Forum: LulzBot TAZ
Topic: Taz 6 Motion Controlls
Replies: 5
Views: 466

Re: Taz 6 Motion Controlls

You can find the full Marlin info along with source for compiling your own here: http://download.lulzbot.com/Software/Marlin/
by Brent.I
Mon Sep 09, 2019 11:06 am
Forum: Filament
Topic: Matter Hackers Build Series PLA - Profile
Replies: 9
Views: 696

Re: Matter Hackers Build Series PLA - Profile

The biggest one is probably the default temperature. If you find you need to change the default printing temps, be sure to look at the wiping and probing temps as well. Chances are these will need to be adjusted in the same direction as the other printing temps to help ensure good cleaning and prob...
by Brent.I
Wed Aug 07, 2019 10:34 am
Forum: LulzBot TAZ
Topic: HS+ Head Taz 6 Major Issues!
Replies: 5
Views: 538

Re: HS+ Head Taz 6 Major Issues!

ROW6 wrote:
Wed Aug 07, 2019 6:28 am
Thanks for all the help here to get me rolling.
We are glad you got it sorted! That is new one I hadn't heard of before, and will keep an eye out for it. We appreciate the update.
by Brent.I
Tue Aug 06, 2019 11:01 am
Forum: LulzBot TAZ
Topic: HS+ Head Taz 6 Major Issues!
Replies: 5
Views: 538

Re: HS+ Head Taz 6 Major Issues!

Also, I am using Cura for Lulzbot 3.3.32 and printing over the air with octoprint 1.3.11 Hmm, I would first recommend updating to Cura 3.6.18 as the 3.2.32 version is quite a bit outdated. You can see all of the improvements we have made sense then here: https://code.alephobjects.com/w/cura-lulzbot...