Search found 49 matches

by marcio
Thu Aug 01, 2019 8:36 am
Forum: Software
Topic: Option to Clear Firmware from Control Box?
Replies: 2
Views: 444

Re: Option to Clear Firmware from Control Box?

If you started with dual extruder FW, you will need to keep the dual extruder connected so that it matches the firmware on the machine. Then, you will flash the single extruder FW with Cura. After this completes, the printer will reboot into the Single Extruder FW, but it will MIN_TEMP immediately b...
by marcio
Tue Jun 25, 2019 10:07 am
Forum: Software
Topic: simplification of z-height adjustment screen
Replies: 3
Views: 420

Re: simplification of z-height adjustment screen

Great idea in principle, in practice it is much harder to do. All Marlin adjustment screens look exactly the same and place the text in the very middle. The Z-offset screen overlays a graphic on top of that standard screen, but cannot change the placement of the underlying text. Neither one of the a...
by marcio
Fri Aug 24, 2018 4:02 pm
Forum: Software
Topic: Marlin 1.1.9 upstream released
Replies: 8
Views: 1348

Re: Marlin 1.1.9 upstream released

A beta release of version 1.1.9.10 has just been pushed to "code.alephobjects.com" (binaries here: https://devel.alephobjects.com/lulzbot/software/Marlin/1.1.9.10 ). This version addresses some issue identified with 1.1.9.9, including potential probing issues with previous generation printers (i.e. ...
by marcio
Fri Aug 10, 2018 7:48 am
Forum: Software
Topic: Marlin 1.1.9 upstream released
Replies: 8
Views: 1348

Re: Marlin 1.1.9 upstream released

Are you making any changes to the Marlin source outside of Configuration.h and Configuration_adv.h? Yes. Although we try pushing changes upstream, to get parity between what we use and what you can get from the Marlin repos, the process is long and slow. Right now there are several modification in ...
by marcio
Fri Jul 27, 2018 1:15 pm
Forum: Software
Topic: Custom Bootscreen
Replies: 2
Views: 514

Re: Custom Bootscreen

That error message isn't very helpful. I would need to see the compiler messages from above to see what the issue was. Anyhow, you need to remove our modifications to the function lcd_custom_bootscreen to re-enable the customization feature. The function would look like this: void lcd_custom_bootscr...
by marcio
Wed Jan 31, 2018 12:18 pm
Forum: Software
Topic: G-code for running two filaments simultaneously
Replies: 1
Views: 574

Re: G-code for running two filaments simultaneously

The stock FW has not been compiled to allow for this. However, Marlin does have a MIXING_EXTRUDER option that can be enabled in "Configuration_Adv.h". If you recompile our FW from source with that enabled, it should allow you to experiment with that feature. /** * "Mixing Extruder" * - Adds a new co...
by marcio
Tue Jan 30, 2018 10:11 am
Forum: Software
Topic: TAZ5 Aerostruder firmware issues
Replies: 6
Views: 2810

Re: TAZ5 Aerostruder firmware issues

When I stop a print, it turns the heaters to zero... This is really irritating, since 9 times out of 10 I'm just stopping to remove a bad first layer and make an adjustment or something before restarting. All the temperature profiles are gone. Resetting the heaters wouldn't be so bad if I could jus...
by marcio
Mon Jan 08, 2018 11:11 am
Forum: Hardware
Topic: IMPORTANT! Problem with Dual V3 and/or new Cura
Replies: 49
Views: 10752

Re: IMPORTANT! Problem with Dual V3 and/or new Cura

BTW, my post above applies only to Mini users. TAZ 6 users have for the most part been spared the numerous start GCODE changes that have been required to get the various generations of Minis to work.
by marcio
Mon Jan 08, 2018 10:19 am
Forum: Hardware
Topic: IMPORTANT! Problem with Dual V3 and/or new Cura
Replies: 49
Views: 10752

Re: IMPORTANT! Problem with Dual V3 and/or new Cura

FYI, Tried with V1.1.5.70, still bad. Starting G Code even does a G28 Z into the back left bed leveling washer instead of the actual z home switch when commands are sent too fast! A G28 X Y followed by a G28 Z after 4 or 5 seconds works fine. Printing a gcode file from octoprint dosnt. Hi silent_ni...
by marcio
Fri Jan 05, 2018 4:17 pm
Forum: Software
Topic: New firmware (Klipper) on TAZ 6
Replies: 24
Views: 3758

Re: New firmware (Klipper) on TAZ 6

Orias and/or marcio: Do either of you happen to know the Z-offset I should apply after probing the bed washers? I'm guessing I can measure it with my calipers or dig the value out of the Marlin code, but I figured if either of you happened to know already, it might save me some time. Hi Clee, The Z...