Search found 301 matches

by b-morgan
Mon Sep 09, 2019 11:01 am
Forum: LulzBot TAZ
Topic: Convert Aerostruder to 1.75, how?
Replies: 1
Views: 48

Re: Convert Aerostruder to 1.75, how?

I believe the Aerostruder is using mostly E3D parts so you should be able to order from E3D the 1.75mm parts and replace them. You will also need to create new firmware for your modified Aerostruder (the sources are available from LulzBot) and, of course, change settings in your slicer. You could al...
by b-morgan
Mon Sep 09, 2019 10:53 am
Forum: Hardware
Topic: Printer is extruding VERY SLOW
Replies: 2
Views: 100

Re: Printer is extruding VERY SLOW

Unless the printer has specific support for resuming from a power failure, it is highly likely that you won't be able to just "pause" and "resume" a print an hour later successfully. The current state of the printer including feed rates, etc. is spread out over multiple GCode commands with the assum...
by b-morgan
Mon Sep 09, 2019 10:45 am
Forum: Filament
Topic: Matter Hackers Build Series PLA - Profile
Replies: 5
Views: 98

Re: Matter Hackers Build Series PLA - Profile

In reality, there are usually only a couple of changes needed to modify a profile for a new brand of the same type of filament. The biggest one is probably the default temperature. I have found that even within the same brand of the same type, I may have to make small adjustments when switching from...
by b-morgan
Mon Sep 09, 2019 10:33 am
Forum: Software
Topic: Linear Advance with Dual Extrusion
Replies: 4
Views: 845

Re: Linear Advance with Dual Extrusion

The workaround for me was to put it into the main PRINTER start gcode, but I don't think this is the correct way Cura should work. I think Cura should execute the gcode in the correct Hot end start gcode regardless of printing with one, two or both extruders. If Cura executes the appropriate Extrud...
by b-morgan
Sun Sep 01, 2019 5:15 pm
Forum: LulzBot Mini
Topic: Mini 1 keeps stopping with a failed wipe message
Replies: 4
Views: 93

Re: Mini 1 keeps stopping with a failed wipe message

Contact LulzBot support. They are there 24/7 by phone or email. Also, please delete the duplicate post.
by b-morgan
Sun Sep 01, 2019 5:13 pm
Forum: Software
Topic: ColorChange plugin is bugged
Replies: 1
Views: 51

Re: ColorChange plugin is bugged

ColorChange probably suffers from the same issue that PauseAtHeight suffered from. The changes to PauseAtHeightorLayer (or is it LayerorHeight) can be copied over to fix it. The issue has to do with rafts, start gcode Z changes, etc. The plugin needs to identify the "real" layer 1 and start counting...
by b-morgan
Sun Sep 01, 2019 5:09 pm
Forum: Software
Topic: Raspberry Pi Camera/Print Monitor Setup?
Replies: 12
Views: 867

Re: Raspberry Pi Camera/Print Monitor Setup?

Setting up the Raspberry Pi camera is quite complicated and one must need some guidance to set up for the first time. So, I will suggest you visit https://netgears.support/blog/fix-arlo-camera-offline-issues/ to get the entire guidance about this and hope it will help a lot. I wouldn't say "is quit...
by b-morgan
Fri Aug 30, 2019 4:56 pm
Forum: Hardware
Topic: Dual V2 now a boat anchor
Replies: 2
Views: 136

Re: Dual V2 now a boat anchor

LulzBot does have Marlin sources with config files available for all of their toolheads, past and present. Knowing which Marlin thermistor model is currently used should help you find one that uses the same algorithm. The firmware has the ability to adjust the PID values.
by b-morgan
Fri Aug 30, 2019 4:51 pm
Forum: Tutorials
Topic: Temperature ladder
Replies: 3
Views: 614

Re: Temperature ladder

Pick a temperature tower model. The model should have instructions that describe its geometry including a recommended layer height. Using these parameters in your slicer and produce a .gcode file. Edit this .gcode file inserting "M104 Sxxx" commands at the appropriate locations (by layer or by heigh...
by b-morgan
Tue Aug 27, 2019 5:15 pm
Forum: Software
Topic: Cura crashes
Replies: 10
Views: 193

Re: Cura crashes

You might try Ultimaker Cura 4.2.1 instead of CuraLE 3.6.18. You can export profiles from CuraLE and import them into Ultimaker Cura but the settings are almost identical. You will have to create a printer profile for your LulzBot printer but again, you can cut and paste. I was able to get 8 3DBench...