Search found 1510 matches

by Orias
Fri Oct 11, 2019 8:13 am
Forum: LulzBot Mini
Topic: Please help with donated Mini 1
Replies: 11
Views: 544

Re: Please help with donated Mini 1

Reach out over the phone, if the lines are busy, try back again: +1-970-377-1111 x610.
by Orias
Thu Oct 10, 2019 12:37 pm
Forum: LulzBot Mini
Topic: Please help with donated Mini 1
Replies: 11
Views: 544

Re: Please help with donated Mini 1

Reach out to the support team at https://LulzBot.com/Support 1-970-377-1111 x610 today. They can help with the above to make sure that you're setup with the right settings, that'll include the information needed. If it worked with your TAZ 6, there's no reason why it can't work with your Mini.
by Orias
Thu Oct 10, 2019 9:37 am
Forum: Hardware
Topic: bad z-seam on boxes
Replies: 6
Views: 527

Re: bad z-seam on boxes

That's a drastic seam. What's your current setup/profile/etc?
by Orias
Thu Oct 10, 2019 7:08 am
Forum: LulzBot Mini
Topic: Please help with donated Mini 1
Replies: 11
Views: 544

Re: Please help with donated Mini 1

If you post your gcode file you're testing with it'll help confirm that you have Cura LE setup correctly. The nozzle wiping and probing behavior is driven through the start gcode added to every slice.
by Orias
Wed Oct 09, 2019 9:39 am
Forum: Software
Topic: Increase Max Wipe Temp in Cura (above 200 °C)
Replies: 8
Views: 1064

Re: Increase Max Wipe Temp in Cura (above 200 °C)

Be careful with that, abrasive materials like sandpaper can erode your nozzle and change the geometry.
by Orias
Tue Oct 08, 2019 3:29 pm
Forum: Software
Topic: Increase Max Wipe Temp in Cura (above 200 °C)
Replies: 8
Views: 1064

Re: Increase Max Wipe Temp in Cura (above 200 °C)

This information is helpful and can be addressed in material profile updates in Cura LE.

Typically, we set the nozzle cleaning temperature to one lower than the extrusion range. Would you all mind posting your lowest cleaning temperatures you've used for specific nylon materials?
by Orias
Tue Oct 08, 2019 12:12 pm
Forum: LulzBot Mini
Topic: Please help with donated Mini 1
Replies: 11
Views: 544

Re: Please help with donated Mini 1

The LulzBot Mini 1 shipped calibrated and ready, here's a bit of information on how to view your Z-axis offset. This value controls how close to the bed your printer will print. A typical value's above 0.5 mm and under 2 mm. What's yours? https://www.lulzbot.com/learn/tutorials/Z-axis-offset You can...
by Orias
Tue Oct 08, 2019 7:49 am
Forum: LulzBot Mini
Topic: Move wiping motion 2 mm towards front
Replies: 3
Views: 302

Re: Move wiping motion 2 mm towards front

You can also move the cleaning pad holder over a little bit in the desired direction by loosening the two screws securing it to the bed plate. You may also want to check out the Y-axis endstops, they shouldn't be loose.
by Orias
Tue Oct 08, 2019 7:38 am
Forum: Software
Topic: Lulzbot Cura refusing to run
Replies: 1
Views: 186

Re: Lulzbot Cura refusing to run

Grab your log, the information contained within may help: https://code.alephobjects.com/w/cura-lu ... ug_report/
by Orias
Fri Oct 04, 2019 12:28 pm
Forum: LulzBot Mini
Topic: Please help with donated Mini 1
Replies: 11
Views: 544

Re: Please help with donated Mini 1

Hello, I am an educator and someone donated a Lulzbot Mini 1 to me. No graphical interface. I had a Taz 6 but it broke and I can't figure out what's up with that. I have been trying to get this mini working and cannot figure it out and hope someone can help. Reach out to the support team at https:/...