Search found 12 matches

by OyarzoPablo
Fri Jan 04, 2019 1:09 pm
Forum: Filament
Topic: Thin Cover ABS without Warping
Replies: 1
Views: 109

Thin Cover ABS without Warping

Lulzbot Taz 6 with acrylic enclosure without extractor fan at a closed office with an AC ranging from 21-25 C ambient temperature. I'm trying to print a Thin Cover to sell it and can't get it print without it getting warped. If I use brim, then it prints fine. What can I do? I read somewhere using h...
by OyarzoPablo
Thu Jan 03, 2019 10:04 am
Forum: LulzBot TAZ
Topic: Elephan Foot Issue
Replies: 2
Views: 161

Re: Elephan Foot Issue

Imposible. All of those are clean on every print. Maybe a Z offset?
by OyarzoPablo
Wed Dec 19, 2018 12:45 pm
Forum: LulzBot TAZ
Topic: Elephan Foot Issue
Replies: 2
Views: 161

Elephan Foot Issue

TAZ6 using cura
I have it with PLA, PETG and ABS got it better by reducing first layer temperature and flow rate but I got it to the limit.
Could it be a leveling problem?
by OyarzoPablo
Thu Dec 06, 2018 8:46 am
Forum: LulzBot TAZ
Topic: Calibration Cube Taz6
Replies: 5
Views: 189

Re: Calibration Cube Taz6

@zachah Worked great!
NOTE: if you do the test, be sure to rotate the model to match x and y axis. had problems for that.

1) Is there a way to make it permanent? on the setting for any imported STL?
2) What was the other not simpler way?
by OyarzoPablo
Mon Dec 03, 2018 11:54 am
Forum: LulzBot TAZ
Topic: Calibration Cube Taz6
Replies: 5
Views: 189

Re: Calibration Cube Taz6

In Cura or Setting on the Lulzbot?

I wanna get as close as I can, as I've seen many examples prints on the Lulzbot, Ender and Prusa.
by OyarzoPablo
Mon Dec 03, 2018 10:02 am
Forum: LulzBot TAZ
Topic: Calibration Cube Taz6
Replies: 5
Views: 189

Calibration Cube Taz6

Printed the calibration cube of Thingiverse: https://www.thingiverse.com/thing:1278865

From 20x20x20 mm
I got

X = 19.90
Y = 20.15
Z = 19.80

How do I proced to take these values closer to 20mm?
by OyarzoPablo
Tue Aug 07, 2018 3:19 pm
Forum: Software
Topic: Upgrading firmware from command line?
Replies: 0
Views: 106

Upgrading firmware from command line?

can you upgrade lulzbot firmware from linux command line?
by OyarzoPablo
Sun Jun 24, 2018 7:36 pm
Forum: Filament
Topic: Polysmooth Profile
Replies: 1
Views: 304

Polysmooth Profile

1) Does anybody have a profile for the Polysmooth material?

I'm getting excess material on the sides (probably because of bad retraction settings) using the PLA Verbatim profile. I have the Taz 6 with the stock hot end...

2) Is there a tutorial on testing a material and creating a profile for it?
by OyarzoPablo
Thu May 10, 2018 3:28 pm
Forum: LulzBot TAZ
Topic: Comprehensive List of TAZ Modifications
Replies: 73
Views: 67038

Re: Comprehensive List of TAZ Modifications

piercet wrote:
Thu May 10, 2018 8:41 am
Depends on which Taz version. There are newer ones for the 6 that I haven't got around to adding on the list yet. But most of them will still work wth a 3-5.
I'm looking for mods specifically for the Taz 6
by OyarzoPablo
Wed May 09, 2018 5:20 pm
Forum: LulzBot TAZ
Topic: Comprehensive List of TAZ Modifications
Replies: 73
Views: 67038

Re: Comprehensive List of TAZ Modifications

I see many of those mods listed that hasn't been touched in years (including the original post), are they still "good"?