Search found 36 matches

by B-Hep-Spring
Mon May 27, 2019 9:55 am
Forum: Hardware
Topic: Wiring Harness of The Taz 6 Head
Replies: 2
Views: 102

Wiring Harness of The Taz 6 Head

Im looking for a source of the plug and pins that Lulzbot use for connecting the head to the printer (the plug with arrows for alignment on it) I think lulzbot sell the pins but im also after the plastic bit that holds the pins does anyone know what this part is ie molex ??? any help appreciated/
by B-Hep-Spring
Mon May 27, 2019 9:52 am
Forum: Hardware
Topic: Taz 6, moving filament reel up top, use filament guide tube or no?
Replies: 5
Views: 143

Re: Taz 6, moving filament reel up top, use filament guide tube or no?

I did the same thing BUT I found with the std head the filament would unwind itself a lot??? but with the Aeroe head this has stoped I did print an a Auto rewind spool holder which works but I wouldn't use the guid Tube.
by B-Hep-Spring
Wed May 08, 2019 12:35 pm
Forum: Hardware
Topic: Taz 6 and the two New printers with modular Bed
Replies: 2
Views: 698

Re: Taz 6 and the two New printers with modular Bed

that sucks, thought this would have been sorted.
by B-Hep-Spring
Wed May 01, 2019 12:30 pm
Forum: News and Announcements
Topic: mosaic palette 2?
Replies: 1
Views: 1799

Re: mosaic palette 2?

I have a Pallette Pro cant see this being supported by Lulzbot only 3.0 fillamanet
by B-Hep-Spring
Wed May 01, 2019 11:43 am
Forum: Hardware
Topic: Taz 6 and the two New printers with modular Bed
Replies: 2
Views: 698

Taz 6 and the two New printers with modular Bed

with the development of the work horse and the Pro ?? they seem to be using the modular bed??? does this mean they have overcome the sagging heater plate and the washer issue we all felt with the Taz 6 Modular bed upgrade,, if so how have they implemented this???? and will we be able to buy these pa...
by B-Hep-Spring
Sat Apr 06, 2019 12:25 pm
Forum: Filament
Topic: Polydissolve S1 - Total Bust
Replies: 6
Views: 867

Re: Polydissolve S1 - Total Bust

for me Id be thinking the Polydesolve is suspect if its brittle, I have limited knowledge of desolveable supports but I have had problems say with pva sticking to NgenLux where it just would not stick I personally would try some other dissolvable material and go from there...yes its a bummer but it ...
by B-Hep-Spring
Mon Feb 18, 2019 1:43 pm
Forum: LulzBot TAZ
Topic: a little worried right now
Replies: 7
Views: 325

Re: a little worried right now

ritmopat

don't get disheartened before you start,, you picked a decent printer (taz) and results will come, there is a learning curve, you only get out what you put inn.. stick at it youll enjoy it... and when you have a problem ask,,,
by B-Hep-Spring
Tue Feb 05, 2019 1:23 pm
Forum: Software
Topic: Cura 3.2.32 crashing out
Replies: 3
Views: 247

Re: Cura 3.2.32 crashing out

I cleared to cache but it made no difference,, cura went very slow then when I tried to save the project I got pushed out to the dek top.. when I re loaded it was corrupt,, re loaded the model re sliced it but cura was not happy when I re sliced and looked at the layers the sliders had disappeared.....
by B-Hep-Spring
Mon Feb 04, 2019 10:47 am
Forum: Software
Topic: Cura 3.2.32 crashing out
Replies: 3
Views: 247

Re: Cura 3.2.32 crashing out

I also have Cura for Ultimaker installed but that version is 64 bit, reluctant to delete that, will try deleteing the cache.
by B-Hep-Spring
Sun Feb 03, 2019 2:04 pm
Forum: Software
Topic: Cura 3.2.32 crashing out
Replies: 3
Views: 247

Cura 3.2.32 crashing out

Hi All

I've loaded up a STL File for my Taz 6 and when I go to save the project cura crashes out to desk top when I look at the file for the project its 0kb yes the model is quiet tall but it should handle it, any suggestions on how to get cura a little more stable.