Search found 1091 matches

by kmanley57
Fri Jan 18, 2019 10:20 pm
Forum: Software
Topic: S3D ending script cant get G91 to work
Replies: 8
Views: 136

Re: S3D ending script cant get G91 to work

I will try one more time: Relative movements require to know which direction you want to move, thus the (+/-) for the distance to move. Otherwise it will think you want to move to an absolute point. Z-5 move 5 down Z+5 move 5 Up. Z5 move to absolute position 5. < not relative. It can not guess which...
by kmanley57
Fri Jan 18, 2019 6:50 am
Forum: Hardware
Topic: Taz 6 bed leveling problem
Replies: 1
Views: 98

Re: Taz 6 bed leveling problem

It sounds like you're talking about the tapping on the washers on the corners, and not the switch press. I would check in the control box and make sure the sense wires have not fallen off the connector.

https://ohai.lulzbot.com/project/taz6-c ... bly/taz-6/ Step 6 EL-HR0081 connections
by kmanley57
Thu Jan 17, 2019 4:51 pm
Forum: LulzBot TAZ
Topic: Selection knob not working?
Replies: 1
Views: 47

Re: Selection knob not working?

You will see a small ~8 pin connector on the control board from the LCD, that is what the knob & SD card communicate through to the RAMBo. I do not remember which connector on the back of the LCD that is also.
by kmanley57
Thu Jan 17, 2019 4:43 pm
Forum: Software
Topic: S3D ending script cant get G91 to work
Replies: 8
Views: 136

Re: S3D ending script cant get G91 to work

im tying to get my ending script when finished to raise up 5mm then move to x and y position but cant seem to get it to work when I look at the line G1 Z20 E-5 X-20 Y-20 F3000 and say the print height is 50mm height it is dropping to the Z20 height. its like it doesent recognise the relative positi...
by kmanley57
Wed Jan 16, 2019 7:52 am
Forum: LulzBot Mini
Topic: Bed leveling issue
Replies: 2
Views: 63

Re: Bed leveling issue

With the printer off and unplugged measure from the nozzle to the printer frame. You look to have a short between them or your control board has failed.
by kmanley57
Sun Jan 06, 2019 8:42 am
Forum: LulzBot TAZ
Topic: Modular Bed fitting to TAZ 6
Replies: 16
Views: 282

Re: Modular Bed fitting to TAZ 6

Make sure the edges of the heating pad is not catching on the flex corners, the picture I looked, at the metal plate is sitting about 1MM higher than it should be in the corner pocket. You may need to loosen the two screws on them and adjust the corners out slightly to get the metal plate to sit bet...
by kmanley57
Sat Jan 05, 2019 8:55 am
Forum: LulzBot TAZ
Topic: Modular Bed fitting to TAZ 6
Replies: 16
Views: 282

Re: Modular Bed fitting to TAZ 6

Checking my Taz 6 it measures 10 MM to the top of the modular bed glass plate. I had a problem at first with the washers not sitting flat, but on second attempt they worked fine.

YMMV....
by kmanley57
Thu Dec 27, 2018 7:26 am
Forum: LulzBot TAZ
Topic: TAZ 6 IGUS bearing failure / wearing out
Replies: 3
Views: 643

Re: TAZ 6 IGUS bearing failure / wearing out

It is pretty easy to change the bearings on the bed. I can do it with the bed/carriage still on the machine though. :lol:

LOTS of practice!
by kmanley57
Wed Dec 19, 2018 6:34 pm
Forum: LulzBot Mini
Topic: Mini Z motor grinding noise and binding
Replies: 9
Views: 221

Re: Mini Z motor grinding noise and binding

The built-in thermal protection circuit on the driver chip should prevent too much damage, but since the Z axis has 2 motors loading it it will thermally shut down before the other two(X/Y). Getting the fan working again should be all you need, if it does not fix then ?????
by kmanley57
Tue Dec 18, 2018 6:50 am
Forum: LulzBot Mini
Topic: Mini Z motor grinding noise and binding
Replies: 9
Views: 221

Re: Mini Z motor grinding noise and binding

Have you tried to loosen the X axis belt/rods? It may be a slight binding from them pulling or pushing the end pieces out of alignment. Thus putting pressure on the smooth rods on the Z axis.