Search found 1105 matches

by kmanley57
Mon Feb 04, 2019 7:10 am
Forum: LulzBot TAZ
Topic: V3 dual head extruder wiring problem on Taz 5
Replies: 3
Views: 87

Re: V3 dual head extruder wiring problem on Taz 5

I think both cold end fans are run from just one of the extruder connectors. I have not wanted a new dual extruder so I can not help you with any details and would recommend AO support or others that have one for that.
by kmanley57
Sun Feb 03, 2019 1:22 pm
Forum: LulzBot TAZ
Topic: Replacement nozzles for Taz4 Budaschnozzle
Replies: 9
Views: 277

Re: Replacement nozzles for Taz4 Budaschnozzle

You do not want to put tape on the nozzle threads, you want good metal2metal contact. As for tightness they are aluminum nozzles and very soft while heated.
by kmanley57
Sun Feb 03, 2019 1:13 pm
Forum: LulzBot TAZ
Topic: V3 dual head extruder wiring problem on Taz 5
Replies: 3
Views: 87

Re: V3 dual head extruder wiring problem on Taz 5

Well the pins you're wondering about are for 3 pins the Taz 5 does not have/use. One of which is just a guide pin, the two purple wires are the X-Max limit switch I believe. No! the pins are fine - no need to change them. Extruder pin-out drawing. http://devel.lulzbot.com/TAZ/Juniperbush/production_...
by kmanley57
Sun Jan 27, 2019 12:09 pm
Forum: LulzBot TAZ
Topic: What material is the TAZ 6 flexible bed corners ?
Replies: 5
Views: 168

Re: What material is the TAZ 6 flexible bed corners ?

I looked at the gcode file on the devel.lulzbot.com site in the production parts directory for the printer Model for that release of printer. :geek:
by kmanley57
Sun Jan 27, 2019 1:19 am
Forum: LulzBot TAZ
Topic: What material is the TAZ 6 flexible bed corners ?
Replies: 5
Views: 168

Re: What material is the TAZ 6 flexible bed corners ?

Well the print file says Ninjaflex.
by kmanley57
Thu Jan 24, 2019 6:04 pm
Forum: LulzBot Mini
Topic: Inadequate hot end heater power (Mini 1)
Replies: 3
Views: 109

Re: Inadequate hot end heater power (Mini 1)

I think you would need a higher wattage supply.
by kmanley57
Fri Jan 18, 2019 10:20 pm
Forum: Software
Topic: S3D ending script cant get G91 to work
Replies: 8
Views: 259

Re: S3D ending script cant get G91 to work

I will try one more time: Relative movements require to know which direction you want to move, thus the (+/-) for the distance to move. Otherwise it will think you want to move to an absolute point. Z-5 move 5 down Z+5 move 5 Up. Z5 move to absolute position 5. < not relative. It can not guess which...
by kmanley57
Fri Jan 18, 2019 6:50 am
Forum: Hardware
Topic: Taz 6 bed leveling problem
Replies: 1
Views: 166

Re: Taz 6 bed leveling problem

It sounds like you're talking about the tapping on the washers on the corners, and not the switch press. I would check in the control box and make sure the sense wires have not fallen off the connector.

https://ohai.lulzbot.com/project/taz6-c ... bly/taz-6/ Step 6 EL-HR0081 connections
by kmanley57
Thu Jan 17, 2019 4:51 pm
Forum: LulzBot TAZ
Topic: Selection knob not working?
Replies: 1
Views: 78

Re: Selection knob not working?

You will see a small ~8 pin connector on the control board from the LCD, that is what the knob & SD card communicate through to the RAMBo. I do not remember which connector on the back of the LCD that is also.
by kmanley57
Thu Jan 17, 2019 4:43 pm
Forum: Software
Topic: S3D ending script cant get G91 to work
Replies: 8
Views: 259

Re: S3D ending script cant get G91 to work

im tying to get my ending script when finished to raise up 5mm then move to x and y position but cant seem to get it to work when I look at the line G1 Z20 E-5 X-20 Y-20 F3000 and say the print height is 50mm height it is dropping to the Z20 height. its like it doesent recognise the relative positi...