Search found 97 matches

by catzcradle
Wed Feb 01, 2017 12:15 pm
Forum: LulzBot TAZ
Topic: Upgrading toolhead harness
Replies: 3
Views: 1024

Re: Upgrading toolhead harness

Thanks!
by catzcradle
Wed Feb 01, 2017 1:18 am
Forum: LulzBot TAZ
Topic: Upgrading toolhead harness
Replies: 3
Views: 1024

Upgrading toolhead harness

Been searching the forums, and Lulzbot now sells a nice toolhead harness replacement for the machine, which I would like to get for my oldest taz5, but also want to retrofit my older toolheads, and I can't find the mating connector for this https://www.digikey.com/product-detail/en/molex-connector-c...
by catzcradle
Tue Jan 31, 2017 8:02 pm
Forum: LulzBot TAZ
Topic: Hardware or Firmware
Replies: 3
Views: 714

Re: Hardware or Firmware

Accel was 500 on the slower taz, and 1000 on the faster one. All other settings were the same.
by catzcradle
Mon Jan 30, 2017 1:34 pm
Forum: LulzBot TAZ
Topic: Hardware or Firmware
Replies: 3
Views: 714

Re: Hardware or Firmware

Thanks, I'll give that a try
by catzcradle
Sun Jan 29, 2017 6:45 pm
Forum: LulzBot TAZ
Topic: Hardware or Firmware
Replies: 3
Views: 714

Hardware or Firmware

I've worked to dial in my two taz 5's to be able to run from the same profile, which saves me a little hassle. However, I've finally confirmed something I've suspected for a while. One printer is slower than the other. On a 3 hr print, it's about 15 minutes off printing the identical gcode sent at t...
by catzcradle
Tue Sep 13, 2016 8:16 pm
Forum: Software
Topic: What supports?
Replies: 3
Views: 898

Re: What supports?

It looks like the option to support from build plate only is on. Use the everywhere option.
by catzcradle
Sun Sep 11, 2016 1:06 pm
Forum: Software
Topic: taz 6 extruder assy on taz 5 firmware change?
Replies: 0
Views: 865

taz 6 extruder assy on taz 5 firmware change?

I'm printing out a mangrove extruder assy. I've noticed that the hot end location in relation to the screw mount to the x-carriage is different. Mangrove is almost in line with the hot end, where the taz 5 is off-center more. Do I need to do something to the firmware to use the new carriage/extruder...
by catzcradle
Fri Sep 09, 2016 1:15 am
Forum: LulzBot TAZ
Topic: (Heated) enclosure for taz 6?
Replies: 6
Views: 4011

Re: (Heated) enclosure for taz 6?

https://www.amazon.com/filament-Makerbo ... n+petg+3mm

I still sometimes get warping on certain geometries with abs, but not nearly as much.
by catzcradle
Sat Aug 20, 2016 2:59 am
Forum: LulzBot TAZ
Topic: Taz 5 extruder suddenly not getting all the way to temp
Replies: 5
Views: 1331

Re: Taz 5 extruder suddenly not getting all the way to temp

Oddly enough, it only did it that one day. The rest of the prints have been fine, so I'll just have to keep an eye on it. I use s3d. But thanks for the info, I'll keep that in mind.
by catzcradle
Tue Aug 09, 2016 4:46 pm
Forum: LulzBot TAZ
Topic: Taz 5 extruder suddenly not getting all the way to temp
Replies: 5
Views: 1331

Re: Taz 5 extruder suddenly not getting all the way to temp

So, if I manually pre-heat the head, it heats up just fine. Going to run another print and watch the temp.