Search found 49 matches

by bladerunner
Thu Mar 03, 2016 1:28 pm
Forum: Software
Topic: Gcodes... Where to find them?
Replies: 4
Views: 1065

Gcodes... Where to find them?

Howdy folks, Just wondering if there was a comprehensive list of the standard Gcodes that are used for the Mini? These are the ones that I have found so far... M501 (to see the current values) M92 E800 (Change 800 to whatever your value is) M500 (Saves your changes) M501 (Verify the changes stayed) ...
by bladerunner
Thu Mar 03, 2016 1:24 pm
Forum: LulzBot Mini
Topic: New Mini Owner - How to ensure my Mini is Optimal?
Replies: 22
Views: 4597

Re: New Mini Owner - How to ensure my Mini is Optimal?

Hmmm... went back and did it again and it worked without the quotations this time. *shurg*

At any rate, I calibrated my e-steps (finally got my hands on a caliper) and my settings changed from 833 to 822. Does that much of a change seem normal?
by bladerunner
Thu Mar 03, 2016 12:46 pm
Forum: Filament
Topic: ABS Woes - Need Assistance (pics attached)
Replies: 12
Views: 3621

Re: ABS Woes - Need Assistance (pics attached)

Thanks David,

I should have mentioned that the fan was off on all of these. Building an enclosure is definitely something that is on my agenda. However, after switching back to HIPS I'm still have a number of issues.
by bladerunner
Thu Mar 03, 2016 12:39 pm
Forum: LulzBot Mini
Topic: New Mini Owner - How to ensure my Mini is Optimal?
Replies: 22
Views: 4597

Re: New Mini Owner - How to ensure my Mini is Optimal?

Odd, because if I just put in the code nothing happened except for the code would appear in the flow, but if I used the quotations the command would work.
by bladerunner
Thu Mar 03, 2016 9:34 am
Forum: Filament
Topic: ABS Woes - Need Assistance (pics attached)
Replies: 12
Views: 3621

ABS Woes - Need Assistance (pics attached)

Hi gang, As I've mentioned before, I'm new to 3D printing as of last week, and aside from my initial octopus test print, I haven't had what I would consider a successful print since. Very frustrating. I'm hoping the community experts can help me trace down the issue(s) and help me resolve them. Here...
by bladerunner
Thu Mar 03, 2016 8:42 am
Forum: Filament
Topic: HIPS and Lulzbot Mini question...
Replies: 17
Views: 4888

Re: HIPS and Lulzbot Mini question...

CoParaTech, you had mentioned that you had good success printing HIPS with Cura. I am not, but my issues may also be printer setup and my own inexperience. Would you mind posting your Cura HIPS settings so I can compare. I'd like to try your settings and see if I can get a good print. Haven't had mu...
by bladerunner
Wed Mar 02, 2016 8:17 pm
Forum: LulzBot Mini
Topic: New Mini Owner - How to ensure my Mini is Optimal?
Replies: 22
Views: 4597

Re: New Mini Owner - How to ensure my Mini is Optimal?

Ahhh nevermind. You have to use the " "'s Duh! :D
by bladerunner
Wed Mar 02, 2016 8:17 pm
Forum: LulzBot Mini
Topic: New Mini Owner - How to ensure my Mini is Optimal?
Replies: 22
Views: 4597

Re: New Mini Owner - How to ensure my Mini is Optimal?

When I type M501 in the command line, nothing happens.
by bladerunner
Wed Mar 02, 2016 5:43 pm
Forum: LulzBot Mini
Topic: New Mini Owner - How to ensure my Mini is Optimal?
Replies: 22
Views: 4597

Re: New Mini Owner - How to ensure my Mini is Optimal?

In Cura where is the standard E-Steps setting? If I go into "Machine Settings" it currently shows the "E-Steps per 1mm filament = 0"

Is there another place I should be looking?
by bladerunner
Wed Mar 02, 2016 9:43 am
Forum: LulzBot Mini
Topic: New Mini Owner - How to ensure my Mini is Optimal?
Replies: 22
Views: 4597

Re: New Mini Owner - How to ensure my Mini is Optimal?

Randy8, thanks for the feedback!

A few questions. Excuse my ignorance...

What is an E-step? In that documentation you gave a link for it mentions to load Pronterface. What is that? And where do I find it?

Thanks!