Search found 144 matches

by mrvanes
Wed Sep 13, 2017 1:51 am
Forum: Software
Topic: Marlin 1.1 config for TAZ6?
Replies: 111
Views: 16532

Re: Marlin 1.1 config for TAZ6?

I own a Mini, bed = 15x15cm, so much less room for error in rear left. So far, first layer extrusion (skirt) is fine throughout the whole bed. I really think what you're seeing is an amplification of what is already slightly wrong with your TAZ, the new 3-probe leveling just makes it more visible. Y...
by mrvanes
Tue Sep 12, 2017 12:32 am
Forum: Software
Topic: Marlin 1.1 config for TAZ6?
Replies: 111
Views: 16532

Re: Marlin 1.1 config for TAZ6?

Another request * Implementation of linear pressure control * * Assumption: advance = k * (delta velocity) * K=0 means advance disabled. * See Marlin documentation for calibration instructions. */ #define LIN_ADVANCE #if ENABLED(LIN_ADVANCE) #define LIN_ADVANCE_K 0 If you define LIN_ADVANCE_K defaul...
by mrvanes
Fri Sep 08, 2017 2:28 am
Forum: Software
Topic: Marlin 1.1 config for TAZ6?
Replies: 111
Views: 16532

Re: Marlin 1.1 config for TAZ6?

http://marlinfw.org/docs/gcode/M206.html

I now finally understand why M206 isn't doing what I expected: it offsets the coordinate space as a whole, that's why G1 Z2 was bed level after M206 Z2!

Ok, will rethink my sins and the future use of M206 now.
by mrvanes
Fri Sep 08, 2017 12:39 am
Forum: Software
Topic: Marlin 1.1 config for TAZ6?
Replies: 111
Views: 16532

Re: Marlin 1.1 config for TAZ6?

Is the bed end stop treated as a probe point now? My taz6 only probed 3 points: build plate endstop-->wipe-->front left-->front right-->rear right-->**not rear left-->heat up nozzle position. Yes, that is the new probe sequence. I was surprised to see it too, but looking at the code it's "by design...
by mrvanes
Thu Sep 07, 2017 11:24 am
Forum: Software
Topic: Marlin 1.1 config for TAZ6?
Replies: 111
Views: 16532

Re: Marlin 1.1 config for TAZ6?

Hmm... in my experience M206 perfectly fits the Z_MAX adjust purpose? It consistently adds an offset to Z after it was homed using G28, automatically from EEPROM. I'm stumped!? But, you're right, your latest fw 1.1.5.3, without my patches from this post leaves Z exactly home_offset too close to the ...
by mrvanes
Thu Sep 07, 2017 7:49 am
Forum: Software
Topic: Marlin 1.1 config for TAZ6?
Replies: 111
Views: 16532

Re: Marlin 1.1 config for TAZ6?

My problem is not restoring old G92 behaviour and I don't have a problem with HAS_POSITION_SHIFT in my configuration. I do think M206 is a better (more userfriendly) way to compensate for different extruder dimensions because it's storable in EEPROM and thus behaves independant from default start gc...
by mrvanes
Wed Sep 06, 2017 8:15 am
Forum: Software
Topic: Marlin 1.1 config for TAZ6?
Replies: 111
Views: 16532

Re: Marlin 1.1 config for TAZ6?

Try this. Manually move the nozzle to the top of one of the bed washers and type "G92 Z1". What this would do in past firmwares is set the Z position to 1 so that now the bed itself was roughly at 0. However, in Marlin 1.1.4 with WORKSPACE_OFFSETS, if you do this, the G92 will adjust the travel lim...
by mrvanes
Tue Sep 05, 2017 7:47 am
Forum: Software
Topic: Marlin 1.1 config for TAZ6?
Replies: 111
Views: 16532

Re: Marlin 1.1 config for TAZ6?

How I solved M206 and fixed failing probes After meticulous measuring and probing it turns out that my nozzle is at Z:161, even with the E3D replacement nozzle sticking out 1mm lower than the original? Which made the Z error (with original M206 Z-1) a total of 3mm! So, either my Mini is completely ...
by mrvanes
Sun Sep 03, 2017 4:08 am
Forum: Software
Topic: Marlin 1.1 config for TAZ6?
Replies: 111
Views: 16532

Re: Marlin 1.1 config for TAZ6?

Here's the detailed output of a G29 V4, failing on LULZBOT_ABL_PROBE_PT_2 Send: G29 V4 Recv: G29 Auto Bed Leveling Recv: Bed X: 0.000 Y: -6.000 Z: -3.371 Recv: Rewiping Recv: PROBE FAIL CLEAN NOZZLE Recv: Error:Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is res...
by mrvanes
Fri Sep 01, 2017 12:41 am
Forum: Software
Topic: Marlin 1.1 config for TAZ6?
Replies: 111
Views: 16532

Re: Marlin 1.1 config for TAZ6?

Menissalt wrote:
Thu Aug 31, 2017 3:48 pm
Is there an easier way to download from this site? I'm only able to do it one file at a time.
I gave you the "browse" link, here's the overview with git clone links:
https://code.alephobjects.com/diffusion ... ory/devel/