Search found 150 matches

by nuroo
Wed Aug 16, 2017 9:13 pm
Forum: LulzBot TAZ
Topic: SD card plastic broke off inside card reader, Taz6
Replies: 2
Views: 667

SD card plastic broke off inside card reader, Taz6

Must be the unlucky one. Had my Taz 6 since April, its been a learning experience. I'm happy with it. SD card has become my preferred way to print. Learned the hard way not to have a computer attached by USB while printing. If the computer reboots it will initialize the USB port and the Taz will fre...
by nuroo
Tue Aug 15, 2017 10:01 am
Forum: Filament
Topic: Layers. Flexystruder
Replies: 1
Views: 763

Re: Layers. Flexystruder

This can be accomplished easily in simplify3d and prusa slic3r, maybe new version Cura can do also I'm not sure. But in old version Cura it cannot.
by nuroo
Tue Aug 15, 2017 6:41 am
Forum: Filament
Topic: Inland PLA quality issues
Replies: 5
Views: 2418

Re: Inland PLA quality issues

I wanted to test the idea of printing a semi transparent skull and then putting a light inside it as seen on YouTube. Anyway since microcenter is close by car I picked up some of their natural pla, to test the idea. Printed the skull fine, and since the natural filament was already on the printer I ...
by nuroo
Mon Aug 14, 2017 11:32 am
Forum: Software
Topic: Cura2 LulzBot Edition Beta Testers Needed!
Replies: 57
Views: 14748

Re: Cura2 LulzBot Edition Beta Testers Needed!

Please dont ignor my 1st post above.

When using the flexdually in new software it assumes the nozzle size is 0.5. The flexdually's are 0.6
by nuroo
Mon Aug 14, 2017 11:20 am
Forum: Software
Topic: Cura2 LulzBot Edition Beta Testers Needed!
Replies: 57
Views: 14748

Re: Cura2 LulzBot Edition Beta Testers Needed!

Im trying the software out. I like the added options. I would love if you guys added the ability to use the flexdually front extruder only. There are times when you only need to print a flexible model, this is not possible in old or new software. Say you need feet for the bottom of a model to keep i...
by nuroo
Fri Jul 21, 2017 7:44 am
Forum: LulzBot TAZ
Topic: Flexydually v2, help printing with flexy only
Replies: 4
Views: 1044

Re: Flexydually v2, help printing with flexy only

Well I usually leave the X/Y offsets alone as I already set them in Cura during Dual calibration, so that I just set which extruder to use and Cura offsets it to where it needs to be, to match the rear extruders relative bed position on its own. Which has worked for me since the V1 dual extruder da...
by nuroo
Wed Jul 19, 2017 6:19 am
Forum: LulzBot TAZ
Topic: ABS sticks to plate like insanity! Help.
Replies: 5
Views: 1336

Re: ABS sticks to plate like insanity! Help.

Have a Taz 6. But for those filaments that stick "too" well to the pei sheet I like to use blue tape. I find it better than using pva glue in cases like yours because it releases much easier than glue for me. Also I'm never sure if I'm using to little or to much glue. Bottom finish won't be as nice ...
by nuroo
Tue Jul 18, 2017 9:44 pm
Forum: LulzBot TAZ
Topic: Flexydually v2, help printing with flexy only
Replies: 4
Views: 1044

Flexydually v2, help printing with flexy only

I want to be able to print sometimes with a single flexible filament only on the flexy head. I dont see even basic support in Cura 21.04 to accomplish this goal. A search thru the forums reveals this is a comman request of flexydually owners. My point is it's not easy to print with just the flexy. I...
by nuroo
Tue Jul 11, 2017 1:59 pm
Forum: LulzBot TAZ
Topic: Dual Extruder calculator Taz6
Replies: 15
Views: 7754

Re: Dual Extruder calculator Taz6

So glad I found this post. I've done the "Dual Extruder calculator" 3 or 4 times. But the calibration squares never looked to be better aligned afterwards.

Gonna invert all values and report back. Hope I have enough filament to print out the keychain :?
by nuroo
Wed Jun 14, 2017 7:52 am
Forum: Software
Topic: Underhangs
Replies: 0
Views: 367

Underhangs

https://www.thingiverse.com/thing:919403 remake of: https://www.thingiverse.com/thing:331035 I got the print settings from the original link comments (331035 above) Lulzbot 6 Lulzbot Cura 21.04 IC3D ABS .5 nozzle .22 Layer height 92% - Flow 1.5mm - Top/bottom thickness 1.5mm - Shell thickness 235C -...