Search found 150 matches

by nuroo
Sat Jun 03, 2017 2:21 pm
Forum: LulzBot TAZ
Topic: Bed centered cam mount for taz 6 ???
Replies: 40
Views: 5301

Re: Bed centered cam mount for taz 6 ???

Thanks so much for continuing to refine this design. Looked in Cura at all three iterations side by side. I can tell you v14 will be too tall on the bottom to fit past that big screw. v12b barely fit. But I can test v14 to see if it can support the camera's weight and to see if the print head pass's...
by nuroo
Fri Jun 02, 2017 6:26 am
Forum: LulzBot TAZ
Topic: Bed centered cam mount for taz 6 ???
Replies: 40
Views: 5301

Re: Bed centered cam mount for taz 6 ???

v13c 's clearance between the heat bed and the metal sheet is a good fit. 1st pic is a shot of Taz6 auto leveling on first washer. Then it travels to the opposite washer along the out side of the hot bed. v13c is still in the way as the print head travels across the bed. 20170602_080928.jpg 20170602...
by nuroo
Thu Jun 01, 2017 6:27 pm
Forum: LulzBot TAZ
Topic: Bed centered cam mount for taz 6 ???
Replies: 40
Views: 5301

Re: Bed centered cam mount for taz 6 ???

Does the TAZ 6 autolevel pattern hit that corner?
Yes the taz 6 touches all fours corners during bed level calibration.

Printing v2 now. I will report back...
by nuroo
Thu Jun 01, 2017 4:27 pm
Forum: LulzBot TAZ
Topic: Bed centered cam mount for taz 6 ???
Replies: 40
Views: 5301

Re: Bed centered cam mount for taz 6 ???

https://youtu.be/26MjuRNgJYM The footage above was taken with the mount below www.thingiverse.com/thing:2206950 It's attached to the left washer of the bed, so you at least don't see the bed moving. Since its angled on the bottom the print head clears it no problem. Just hope we can get something wo...
by nuroo
Thu Jun 01, 2017 11:43 am
Forum: LulzBot TAZ
Topic: Bed centered cam mount for taz 6 ???
Replies: 40
Views: 5301

Re: Bed centered cam mount for taz 6 ???

Thanks for taking the time to mod stl's. This is the part you sent b4. I filed it down to fit. Haven't printed the new version yet. But i can tell you it needs to be between 4.7mm-5.0mm thick to fit between build plate and metal plate. I will try version2 tonight. 20170601_131422.jpg 20170601_131500...
by nuroo
Wed May 31, 2017 2:33 pm
Forum: LulzBot TAZ
Topic: Bed centered cam mount for taz 6 ???
Replies: 40
Views: 5301

Re: Bed centered cam mount for taz 6 ???

Didnt fit. Not enough clearance between build plate and the metal sheet underneath it. Maybe I could sand a few mm off.
by nuroo
Tue May 30, 2017 8:35 pm
Forum: LulzBot TAZ
Topic: Bed centered cam mount for taz 6 ???
Replies: 40
Views: 5301

Re: Bed centered cam mount for taz 6 ???

Much appreciated, I'll give it a try !!
by nuroo
Tue May 30, 2017 7:30 pm
Forum: LulzBot TAZ
Topic: Bed centered cam mount for taz 6 ???
Replies: 40
Views: 5301

Bed centered cam mount for taz 6 ???

Those are what I've found so far for the Taz 6...... Pi cam bed mount https://www.thingiverse.com/thing:2125257 (Pi cam quality isn't so hot, even version 2 pi cam, and footage will be off axis. No Gopro mount) Z-axis bed mount https://www.thingiverse.com/thing:1594910 (You see the bed moving during...
by nuroo
Tue Apr 18, 2017 8:50 am
Forum: LulzBot TAZ
Topic: Problem with First Layer
Replies: 3
Views: 872

Re: Problem with First Layer

New Taz owner here. Have same issue. The advice is to lower z offset. Where? If startup gcode - what command? In printer setup, tuning - how?, in cura printer profile, how? I'm assuming after bed leveling. Did u fix it? What I've done so far: Measured filament in several places and averaged. Lowered...
by nuroo
Mon Apr 10, 2017 2:17 pm
Forum: LulzBot TAZ
Topic: Extrusion delay - TAZ 6
Replies: 5
Views: 1740

Re: Extrusion delay - TAZ 6

I've had my Taz 6 for 3 days. Really like it.

Noticing this same issue. I started making 3 line skirts, with big 10mm offset so I can try and grab the little piece of filamemt that doesn't stick to bed and prime the nozzle.

I will try modding the gcode like suggested.