Search found 150 matches

by nuroo
Sat Jan 13, 2018 1:35 pm
Forum: Software
Topic: Linear Advance
Replies: 22
Views: 3655

Re: Linear Advance

Wonder if with new tool heads, Lulzbot jumps on linear advance band wagon
by nuroo
Fri Jan 12, 2018 6:28 pm
Forum: Software
Topic: Octoprint Filament Runout Sensor
Replies: 18
Views: 13418

Re: Octoprint Filament Runout Sensor

Its free floating. Works pretty well like that.

I lack the design skills to make a mount for it. But I'm learning slowly.
by nuroo
Wed Jan 10, 2018 1:03 pm
Forum: Software
Topic: Linear Advance
Replies: 22
Views: 3655

Re: Linear Advance

Have 4 printers, so i decided to wait for metal pei sheet. But Big printers can benefit from linear advance also. Matter of fact my CR10s4 - 400mm x 400mm x 400mm with a bowden extruder and a heavy print bed plugs it off. But finding a good K factor takes longer. For my Taz6's sake I wish Lulzbot wo...
by nuroo
Wed Jan 10, 2018 12:15 pm
Forum: Software
Topic: Linear Advance
Replies: 22
Views: 3655

Re: Linear Advance

This is a choice Lulzbot is making. I dont know the reasons behind their decision. Maybe they will read your post and address the reasons behind their decision. Any1 who was using it on a Lulzbot had it on a beta firmware that had it activated while they were testing it. I can tell you that Prusa ha...
by nuroo
Sat Jan 06, 2018 2:39 pm
Forum: LulzBot TAZ
Topic: Lắp đặt mạng FPT tại Hà Nội chỉ từ 185.000đ
Replies: 2
Views: 1126

Re: Ran out of filament on a large print TAZ6

Quickest easy solution: Upgrade to newest lulzbot firmware for Taz6. It has a hot swap filament change built into the firmware that is much better then older firmware. You still have to monitor print, for a run out. Harder, but still easier the hard wiring a filament sensor and changing firmware to ...
by nuroo
Mon Dec 18, 2017 8:52 pm
Forum: Software
Topic: Lulzbot 6 printing PLA printing circle/extrude issue
Replies: 9
Views: 1179

Re: Lulzbot 6 printing PLA printing circle/extrude issue

w3zl01d wrote:
Mon Dec 18, 2017 6:27 pm
Yes, This has been a problem because my 2cm cube is 20.08 x 20.05 where the height is 20.05
you are right i need to find out those steps because for me it's important that a cylinder will fit in a cylinder hehe

Thanks
actually thats pretty good.
by nuroo
Mon Dec 18, 2017 5:09 pm
Forum: Software
Topic: Lulzbot 6 printing PLA printing circle/extrude issue
Replies: 9
Views: 1179

Re: Lulzbot 6 printing PLA printing circle/extrude issue

Called lulzbot and they say the esteps are correct at 830. so i asked them for the rest of the steps and it seems all the steps are correctly set by the firmware flash. Ok my experience has been different. My extruder came from the factory with a estep sticker (846), factory offset of -1.361. If I ...
by nuroo
Sun Dec 17, 2017 8:25 pm
Forum: Hardware
Topic: Alternative xyz calibration method??
Replies: 1
Views: 573

Alternative xyz calibration method??

The title of this video was "Calibrate your 3D Printer 2 - An Advanced Tutorial" https://www.youtube.com/watch?v=W4CsD5lRvHY My usual method 1st calibrate extruder 2nd find good zoffset 3rd ...... etc...... then print calibration cube, measure it, use formula to correct xyz steps/mm, reprint cube to...
by nuroo
Sun Dec 17, 2017 6:52 pm
Forum: Software
Topic: Lulzbot 6 printing PLA printing circle/extrude issue
Replies: 9
Views: 1179

Re: Lulzbot 6 printing PLA printing circle/extrude issue

I would personally make sure my esteps are correct - first step. If slicer request 100mm, printer should extrude 100mm. Its key to all prints. After that adjust for filament diameter in slicer if desired, (stock profiles are tuned nicely) so it's less important. Only more important if chasing perfec...