Search found 47 matches

by OutcastZeroOne
Sat Jun 30, 2018 1:32 pm
Forum: LulzBot Mini
Topic: Mini 2!
Replies: 29
Views: 3936

Re: Mini 2!

I was able to order the board right from ultimate with no issue. Was $120
by OutcastZeroOne
Thu Jun 28, 2018 1:16 pm
Forum: LulzBot Mini
Topic: Mini 2!
Replies: 29
Views: 3936

Re: Mini 2!

I’m in process of printing out parts for upgrading my mini1 to a mini2,just wondering if there are any parts that are reused so I’m not printing more then is needed. Still have the old stock bed for now, will order the new bed later on.
by OutcastZeroOne
Fri Jun 09, 2017 10:36 pm
Forum: LulzBot Mini
Topic: New controller and firmware
Replies: 12
Views: 3070

Re: New controller and firmware

well, as someone who has worked in the car stereo industry for the past 11 years, I've got a few ideas on noise reduction and things that can cause noise :p So, an update on this. I found a source for the firmware and got it loaded onto the GT2560. Now is just have to change out all the plugs on the...
by OutcastZeroOne
Mon Jun 05, 2017 6:55 pm
Forum: LulzBot Mini
Topic: New controller and firmware
Replies: 12
Views: 3070

Re: New controller and firmware

so dose anyone one have any ideas on what i need to do for settings on this new board? Id like to try and keep the bed leveling settings as much as possible. just wish I could find marlin versions of the mini firmware like i can for the TAZ
by OutcastZeroOne
Sun Jun 04, 2017 1:14 pm
Forum: LulzBot Mini
Topic: New controller and firmware
Replies: 12
Views: 3070

Re: New controller and firmware

I would hope they would use locktight for something like that. That also means heat is needed to release the glue, such as a small torch.
by OutcastZeroOne
Sun Jun 04, 2017 12:42 pm
Forum: LulzBot Mini
Topic: New controller and firmware
Replies: 12
Views: 3070

Re: New controller and firmware

I did try that for a while, but all it seemed to do was lower to motor, and drag the chain over the screw heads. I tried to reposition the pulley on the motor using brand new Allen keys, but they are on so tight they stripped out so I can't reposition the stupid thing to the right elevation. And yes...
by OutcastZeroOne
Sun Jun 04, 2017 12:39 pm
Forum: Software
Topic: Mini firmware
Replies: 6
Views: 1789

Re: Mini firmware

But where do I put it in the line of commands?
by OutcastZeroOne
Sun Jun 04, 2017 12:26 pm
Forum: LulzBot Mini
Topic: New controller and firmware
Replies: 12
Views: 3070

Re: New controller and firmware

My machine is only about 2 months old.

As far as power handling, pretty much every board has one driver for 2 z-axis motors. Even the Mini RAMBo uses one driver for the 2 motors.

What upgrade are you talking about?
by OutcastZeroOne
Sun Jun 04, 2017 11:27 am
Forum: LulzBot Mini
Topic: New controller and firmware
Replies: 12
Views: 3070

Re: New controller and firmware

Ultimately, the boards are similar to each other, what I dont know are the exact settings needed for endstops and setting up the auto leveling. I downloaded the Marlin version for TAZ and fiddeled a bit with it but this is still fairly new to me. Just sucks that 3 weeks after dropping $1050 on a new...
by OutcastZeroOne
Sun Jun 04, 2017 10:03 am
Forum: LulzBot Mini
Topic: New controller and firmware
Replies: 12
Views: 3070

New controller and firmware

So after much testing I've determined that my control board has partially fried itself. So, now I am trying to install a Geeetech GT2560 (Ultimaker clone) in place of the half dead Mini RAMBo but i want to make sure I get the settings right. Im using the Trinamic SilentStepSticks (one more reason fo...