Search found 65 matches

by zachah
Fri Apr 05, 2019 8:51 pm
Forum: LulzBot TAZ
Topic: Did I just kill my TAZ 6?
Replies: 8
Views: 2091

Re: Did I just kill my TAZ 6?

We have fuses available in packs of 3 on our lulzbot.com store page:

https://www.lulzbot.com/store/parts/5-a ... olyfuse-x3
Rambofuses1.jpg
by zachah
Fri Feb 01, 2019 9:28 pm
Forum: LulzBot Mini
Topic: Adding a beeper to the Mini
Replies: 3
Views: 453

Re: Adding a beeper to the Mini

https://reprap.org/wiki/MiniRambo

You can find the revision of the RAMBo board written on the board itself
by zachah
Mon Jan 21, 2019 5:12 pm
Forum: LulzBot Mini
Topic: Auto Level Fail
Replies: 6
Views: 2355

Re: Auto Level Fail

Since our printers use Marlin firmware you can use the G/M code reference on the Marlin FW site:
http://marlinfw.org/meta/gcode/
by zachah
Fri Jan 18, 2019 2:59 pm
Forum: LulzBot Mini
Topic: Bed heater failure
Replies: 5
Views: 1930

Re: Bed heater failure

It looks like we don't have the 1.3 RAMBo in stock currently but we do have the newer 1.4 at this moment. You can use the 1.4 RAMBo as a direct replacement for your Taz 6. https://www.lulzbot.com/store/parts/assembled-rambo-v14-kit-lcd-harnesses https://ohai.lulzbot.com/project/taz6-control-box-asse...
by zachah
Thu Jan 10, 2019 3:14 pm
Forum: Hardware
Topic: Taz 5 Temperature Drops
Replies: 14
Views: 7576

Re: Taz 5 Temperature Drops

If you have access to a digital multimeter you may want to test the voltage of the PSU. Plug the PSU (power supply unit) into a worked outlet, and then measure the DC output of the 4 pins on the output of the PSU. Pins 1 and 2 will be live, while pins 3 and 4 will be ground. You should get 24V DC ou...
by zachah
Wed Jan 09, 2019 9:11 pm
Forum: LulzBot Mini
Topic: Mini 1 stops printing in middle of print.
Replies: 14
Views: 1846

Re: Mini 1 stops printing in middle of print.

What version of Cura software are you currently using?
by zachah
Wed Jan 09, 2019 9:11 pm
Forum: Hardware
Topic: Dual Extruder V3 - Hobbed Shaft Gear Stripped
Replies: 3
Views: 530

Re: Dual Extruder V3 - Hobbed Shaft Gear Stripped

If you haven't already contact us over at support about this stripped out gear.
by zachah
Wed Jan 09, 2019 9:04 pm
Forum: LulzBot TAZ
Topic: TAZ modular bed... metal plate sags.
Replies: 30
Views: 9268

Re: TAZ modular bed... metal plate sags.

If you have some NinjaFlex available: On the Taz 5 print this flexible standoff and place it in the center of the bed: https://devel.lulzbot.com/TAZ/accessories/zebra/Production_parts/printed_parts/Taz5_flexy_support/ 83d3f5836547483567d0cb31f35f40ffb665ecc9.JPG If you've got the Taz 6 try these upd...
by zachah
Thu Jan 03, 2019 3:09 pm
Forum: Hardware
Topic: TAZ 5 Dual Extruder V3 Questions
Replies: 4
Views: 669

Re: TAZ 5 Dual Extruder V3 Questions

We recently started stocking the hot-end kits for the dual extruder V3. https://www.lulzbot.com/store/parts/lulzbot-taz-dual-extruder-v3-hot-end-kit Also e3d has most of the individual parts you would need that we don't stock including the HS volcano nozzles. https://e3d-online.com/lulzbot-spares An...
by zachah
Wed Jan 02, 2019 6:47 pm
Forum: Software
Topic: Z-axis offset woes
Replies: 11
Views: 1731

Re: Z-axis offset woes

https://www.lulzbot.com/content/taz-bed-leveling

The directions above show how to level the bed from completely from scratch.

Follow the entirety of these directions and your bed will be level and your Z-offset correct