Search found 65 matches

by zachah
Mon Sep 17, 2018 1:48 pm
Forum: Hardware
Topic: Estep question
Replies: 3
Views: 616

Re: Estep question

Try lowering the extrusion speed you're using when you calibrate. I've had this issue while trying to push plastic out too fast during a calibration before. Also check the set-screw inside of the small herringbone gear to make sure that's nice and tight against the flat portion of the motor shaft. H...
by zachah
Fri Sep 14, 2018 1:48 pm
Forum: Software
Topic: 3.2.23 not slicing
Replies: 2
Views: 826

Re: 3.2.23 not slicing

Try clearing out your cache. Any time I've run into issues like this clearing out the cache does the trick. It will clear out all of the printers and start fresh. Instructions for clearing out your cache can be found on the download page for your operating system. Ubuntu: https://www.lulzbot.com/lea...
by zachah
Fri Sep 14, 2018 1:48 pm
Forum: Software
Topic: Cura 3.2.23 with flexydually v2 nozzle switch
Replies: 6
Views: 645

Re: Cura 3.2.23 with flexydually v2 nozzle switch

My mistake I had two tabs open with two posts that had similar titles. That cache clearing suggestion was meant for the other post. For this you could try setting your standby temperature 5-10 degrees higher so that the nozzle doesn't need to heat up as much before switching. I've also had luck expe...
by zachah
Thu Sep 13, 2018 2:33 pm
Forum: Software
Topic: Cura 3.2.23 with flexydually v2 nozzle switch
Replies: 6
Views: 645

Re: Cura 3.2.23 with flexydually v2 nozzle switch

Try clearing out your cache. Any time I've run into issues like this clearing out the cache does the trick. It will clear out all of the printers and start fresh. Instructions for clearing out your cache can be found on the download page for your operating system. Ubuntu: https://www.lulzbot.com/lea...
by zachah
Thu Sep 13, 2018 2:23 pm
Forum: Software
Topic: Weird Taz 6 z-probing behavior in 1.1.9+
Replies: 1
Views: 366

Re: Weird Taz 6 z-probing behavior in 1.1.9+

I made a code ticket about this issue and they were able to solve it by editing the start gcode. https://code.alephobjects.com/T3512 Try using this as your start gcode if you've got the standard extruder. ;This G-Code has been generated specifically for the LulzBot TAZ 6 with standard extruder M75 ;...
by zachah
Mon Sep 10, 2018 3:36 pm
Forum: Hardware
Topic: Recommended additional equipment?
Replies: 11
Views: 3326

Re: Recommended additional equipment?

FYI for our printers we recommend never using any kind of wire brush or letting any kind of metal element come in contact with the nozzle. With the way our auto-leveling works the nozzle is electrically connected to the mini RAMBo board making it susceptible to electric static discharge damage throu...
by zachah
Wed Aug 29, 2018 2:31 pm
Forum: Hardware
Topic: Seeking Dual Extruder v2 Metal Parts
Replies: 1
Views: 348

Re: Seeking Dual Extruder v2 Metal Parts

If you get in contact with our sales team they should be able to sell you one of those. There are many small part like this that don't have a listing on the website but can be purchased through sales directly. Just give them that part number PP-MP0086 when you call or email and they should be able t...
by zachah
Thu Aug 16, 2018 1:56 pm
Forum: LulzBot Mini
Topic: Mini 2 nozzle replacement?
Replies: 3
Views: 560

Re: Mini 2 nozzle replacement?

That is a bit strange, but it just looks like an oversight. On the V6 plated copper nozzle stand-alone page it looks like they do have it in 0.5mm, just not on our page...

https://e3d-online.com/v6-nozzles-plated-copper
by zachah
Wed Aug 15, 2018 5:53 pm
Forum: LulzBot Mini
Topic: Mini 2 nozzle replacement?
Replies: 3
Views: 560

Re: Mini 2 nozzle replacement?

e3d-online recently opened a page on their site with nozzles and parts compatible specifically with our tool-heads. https://e3d-online.com/lulzbot-spares WARNING: At Aleph Objects, Inc. we respect your freedom to modify your LulzBot 3D printer. It is important to know that any modifications or attem...
by zachah
Tue Aug 14, 2018 9:48 pm
Forum: Hardware
Topic: Upgrading my TAZ 5
Replies: 9
Views: 2244

Re: Upgrading my TAZ 5

Here's the info I found from the power supplies data sheet. RTH2≧50℃±10℃ Fan on ; RTH2≦40℃±10℃ Fan off (Fan always on for 3.3~5V,Fan ON/OFF control for 12~48V) Which basically sounds to me like the fan is on when the temperature is above ~50℃ and off below ~40℃ http://download.lulzbot.com/retail_par...