Search found 59 matches

by B-Hep-Spring
Thu Jun 27, 2019 12:42 pm
Forum: LulzBot TAZ
Topic: HS Tool Head 0.8 Made a expensive mistake
Replies: 4
Views: 328

Re: HS Tool Head 0.8 Made a expensive mistake

Joe

I stand corrected it must have been a senior moment :(

thank you for your reply is your volcano working well and is the nozzle easy to get out?? hot obvioulsy
by B-Hep-Spring
Wed Jun 26, 2019 1:04 pm
Forum: LulzBot TAZ
Topic: HS Tool Head 0.8 Made a expensive mistake
Replies: 4
Views: 328

HS Tool Head 0.8 Made a expensive mistake

Hi All I purchased the HS Tool Head 0.8 thinking stupidly it was based on the Aeroe head but with hardened drives act,, I find it has a Volcano fitted which is not what I wanted to achieve I want to print with carbon but want to print fairly small parts with a .4 nozzle, which you cant buy in volcan...
by B-Hep-Spring
Wed Jun 19, 2019 12:46 pm
Forum: LulzBot TAZ
Topic: Lulzbot Taz 6: Different Nozzles
Replies: 2
Views: 318

Re: Lulzbot Taz 6: Different Nozzles

I am no expert but id rule the ruby out as its not helpful with bed levelling unless you want to go down that route but I wouldn't its complicated enough without disabling a feature?? - Bed levelling if its the std head I would look at taking the nozzle out either get a replacement from https://itwo...
by B-Hep-Spring
Mon May 27, 2019 9:55 am
Forum: Hardware
Topic: Wiring Harness of The Taz 6 Head
Replies: 2
Views: 348

Wiring Harness of The Taz 6 Head

Im looking for a source of the plug and pins that Lulzbot use for connecting the head to the printer (the plug with arrows for alignment on it) I think lulzbot sell the pins but im also after the plastic bit that holds the pins does anyone know what this part is ie molex ??? any help appreciated/
by B-Hep-Spring
Mon May 27, 2019 9:52 am
Forum: Hardware
Topic: Taz 6, moving filament reel up top, use filament guide tube or no?
Replies: 5
Views: 430

Re: Taz 6, moving filament reel up top, use filament guide tube or no?

I did the same thing BUT I found with the std head the filament would unwind itself a lot??? but with the Aeroe head this has stoped I did print an a Auto rewind spool holder which works but I wouldn't use the guid Tube.
by B-Hep-Spring
Wed May 08, 2019 12:35 pm
Forum: Hardware
Topic: Taz 6 and the two New printers with modular Bed
Replies: 2
Views: 817

Re: Taz 6 and the two New printers with modular Bed

that sucks, thought this would have been sorted.
by B-Hep-Spring
Wed May 01, 2019 12:30 pm
Forum: News and Announcements
Topic: mosaic palette 2?
Replies: 1
Views: 2172

Re: mosaic palette 2?

I have a Pallette Pro cant see this being supported by Lulzbot only 3.0 fillamanet
by B-Hep-Spring
Wed May 01, 2019 11:43 am
Forum: Hardware
Topic: Taz 6 and the two New printers with modular Bed
Replies: 2
Views: 817

Taz 6 and the two New printers with modular Bed

with the development of the work horse and the Pro ?? they seem to be using the modular bed??? does this mean they have overcome the sagging heater plate and the washer issue we all felt with the Taz 6 Modular bed upgrade,, if so how have they implemented this???? and will we be able to buy these pa...
by B-Hep-Spring
Sat Apr 06, 2019 12:25 pm
Forum: Filament
Topic: Polydissolve S1 - Total Bust
Replies: 6
Views: 1273

Re: Polydissolve S1 - Total Bust

for me Id be thinking the Polydesolve is suspect if its brittle, I have limited knowledge of desolveable supports but I have had problems say with pva sticking to NgenLux where it just would not stick I personally would try some other dissolvable material and go from there...yes its a bummer but it ...
by B-Hep-Spring
Mon Feb 18, 2019 1:43 pm
Forum: LulzBot TAZ
Topic: a little worried right now
Replies: 7
Views: 522

Re: a little worried right now

ritmopat

don't get disheartened before you start,, you picked a decent printer (taz) and results will come, there is a learning curve, you only get out what you put inn.. stick at it youll enjoy it... and when you have a problem ask,,,