Search found 59 matches

by B-Hep-Spring
Sat Jan 05, 2019 10:58 am
Forum: LulzBot TAZ
Topic: Modular Bed fitting to TAZ 6
Replies: 18
Views: 1351

Re: Modular Bed fitting to TAZ 6

Thanks for the reply I will have another go I re measured everything and the plates are the same thickness the difference is in the heater plate this adds another 1mm to the height of the plate as this sits into the corners of the printed bed supports... Ill try and re fit if not ill make 11mm pilla...
by B-Hep-Spring
Sat Jan 05, 2019 7:13 am
Forum: LulzBot TAZ
Topic: Modular Bed fitting to TAZ 6
Replies: 18
Views: 1351

Modular Bed fitting to TAZ 6

Hope someone can help me hear, I went to fit the Modular Bed to my TAZ 6, thought this would be a strait swap, when I tighten the 16mm washers down they don't lay flat?? because the heater plate sits in the print corners im 1 mm higher,, when I look at my Stand off they measure 10mm,, when I loof at...
by B-Hep-Spring
Sat Nov 17, 2018 1:53 pm
Forum: Hardware
Topic: Adapter for the Aerostruder V2 Micro..?
Replies: 3
Views: 523

Re: Adapter for the Aerostruder V2 Micro..?

Thanks for letting us know Mine is on order shortly :D
by B-Hep-Spring
Tue Nov 13, 2018 10:54 am
Forum: Hardware
Topic: Adapter for the Aerostruder V2 Micro..?
Replies: 3
Views: 523

Re: Adapter for the Aerostruder V2 Micro..?

I had also read about the Adapter plate :| which did state that they hoped it to be ready by mid September,, I have to say after purchasing the Taz 6 Im a little disappointed that the heads are in such a short supply... I was watching this head to purchase,, but obviously there are problems..
by B-Hep-Spring
Sun Nov 11, 2018 1:15 pm
Forum: LulzBot TAZ
Topic: Dual Head V3 opinions please
Replies: 1
Views: 251

Dual Head V3 opinions please

Hi I am looking to purchase a dual head v3 while Lulzbot are out of stock with them in the UK I have found some in Farnell, I am a bit concerned, if they are old stock??? I seem to remember there was an issue with the Temp on the dual head and found it was a manufacturing fault,, How likely is it th...
by B-Hep-Spring
Thu Nov 01, 2018 9:14 am
Forum: Software
Topic: Taz 6 With S3D setup
Replies: 0
Views: 428

Taz 6 With S3D setup

Hi Im trying to setup S3D to use my Taz 6 STD Head when I produce the code I get G90 M82 M106 S0 M140 S60 M190 S60 M104 S205 T0 M109 S205 T0 this is not in my script, although the majority of this is covered in my script, how do I stop S3D from producing this.. I could just leave it but when it come...
by B-Hep-Spring
Sun Oct 14, 2018 12:41 pm
Forum: LulzBot TAZ
Topic: Taz 6 Modular Bed
Replies: 2
Views: 346

Re: Taz 6 Modular Bed

Thanks for that I split the cost and just get the glass plate for now ,, Thanks for replying
by B-Hep-Spring
Sat Oct 13, 2018 1:01 pm
Forum: LulzBot TAZ
Topic: Taz 6 Modular Bed
Replies: 2
Views: 346

Taz 6 Modular Bed

without disassembling my new Taz 6, is this supplied with the modular bed - https://www.lulzbot.com/store/parts/lul ... bed-heater

just getting confused, I am putting my machine together and have always been used to glass beds ect pei sheets so this looked interesting for me...
by B-Hep-Spring
Sat Oct 13, 2018 12:12 pm
Forum: LulzBot TAZ
Topic: Taz 6 e3d conversion and fan ducts.
Replies: 3
Views: 7730

Re: Taz 6 e3d conversion and fan ducts.

Hi Im new to the TAZ 6 was a little disappointed the std tool head was not a full, V6 setup, the mod you did was this the complete head V6 Mod or was it just the fans,,,if it was a new V6 heat breakers nozzles ect could you point me to some more information on this mod...