# Flexidually

**URL:** <https://forum.lulzbot.com/t/flexidually/1678>\
**Category:** Hardware\
**Created:** [April 23, 2015, 1:22pm UTC](https://forum.lulzbot.com/t/flexidually/1678 "2015-04-23T13:22:11Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![camille.kerbaul](https://avatars.discourse-cdn.com/v4/letter/c/8c91f0/32.png) [@camille.kerbaul](https://forum.lulzbot.com/u/camille.kerbaul)\
**Post date:** [April 23, 2015, 1:22pm UTC](https://forum.lulzbot.com/t/flexidually/1678/1 "2015-04-23T13:22:11Z")

</div>

Hi guys,

The flexidually is out of sotck, but I really need to print a flex / solid part. I allready have a Flexistruder and a Single Extruder Tool Head v2. Can I 3Dprint the flexidually stand and put both my flexistruder and the extruder tool on it ?

I found these files to print the flexidually stand :  
[http://devel.lulzbot.com/TAZ/accessories/dual\_extruder/dual\_extruder-1.0/source/](http://devel.lulzbot.com/TAZ/accessories/dual_extruder/dual_extruder-1.0/source/)

Is it the right way to proceed ?

An other question, I noticed that I need to reflash the printer to print with the felxistruder:  
“IMPORTANT - If installing on a TAZ5.0 or newer printer, you’ll need to reflash the printer with our Flexy TAZ 5 firmware to power the flexystruder.”

Which firmware will I have to use if I want to use my ‘custom’ flexidually ?  
Is there any precaution to take ?

Thanks a lot,  
Camille.

---

<div class="post-metadata">

**Author:** ![Orias](https://sea2.discourse-cdn.com/flex020/user_avatar/forum.lulzbot.com/orias/32/3_2.png) [@Orias](https://forum.lulzbot.com/u/Orias)\
**Post date:** [April 24, 2015, 5:08pm UTC](https://forum.lulzbot.com/t/flexidually/1678/2 "2015-04-24T17:08:27Z")

</div>

We have a simplified firmware update process here: [https://www.lulzbot.com/support/firmware-flashing-through-cura](https://www.lulzbot.com/support/firmware-flashing-through-cura), with this firmware being the one you’ll want to use: [TAZ5 Flexy Firmware](https://devel.lulzbot.com/TAZ/accessories/flexystruder/Marlin_2015Q1_FlexyTAZ5.cpp.hex)

---

<div class="post-metadata">

**Author:** ![Maxime](https://avatars.discourse-cdn.com/v4/letter/m/a9adbd/32.png) [@Maxime](https://forum.lulzbot.com/u/Maxime)\
**Post date:** [April 26, 2015, 7:39pm UTC](https://forum.lulzbot.com/t/flexidually/1678/3 "2015-04-26T19:39:25Z")

</div>

Once installed the Taz5 Flexystruder firmware (“Flexy Taz 5 Ready” on my blue screen), I only have access to one head of two of my FlexyDually.  
  
  
In other words, what firmware should I install to get my FlexyDually (hard and flex head) to work?

Thank you for your quick answer! (We like your printers and bought two of them here.)

---

<div class="post-metadata">

**Author:** ![Orias](https://sea2.discourse-cdn.com/flex020/user_avatar/forum.lulzbot.com/orias/32/3_2.png) [@Orias](https://forum.lulzbot.com/u/Orias)\
**Post date:** [April 27, 2015, 4:43pm UTC](https://forum.lulzbot.com/t/flexidually/1678/4 "2015-04-27T16:43:40Z")

</div>

For the Dual extruder (flexy or otherwise) you’ll want the dual extruder firmware, for the TAZ4/5: [https://devel.lulzbot.com/TAZ/accessories/dual\_extruder/dual\_extruder-1.0/software/Marlin\_dual\_extruder\_taz4-5\_dual\_fan\_control.cpp.hex](https://devel.lulzbot.com/TAZ/accessories/dual_extruder/dual_extruder-1.0/software/Marlin_dual_extruder_taz4-5_dual_fan_control.cpp.hex)

You don’t need a Flexy-specific Dual extruder firmware.