# Linear Advance

**URL:** <https://forum.lulzbot.com/t/linear-advance/5488>\
**Category:** Software\
**Created:** [January 10, 2018, 5:12pm UTC](https://forum.lulzbot.com/t/linear-advance/5488 "2018-01-10T17:12:50Z")\
**Posts on this page:** 3\
**Page:** 2

<div class="post-metadata">

**Author:** ![nuroo](https://avatars.discourse-cdn.com/v4/letter/n/c89c15/32.png) [@nuroo](https://forum.lulzbot.com/u/nuroo)\
**Post date:** [January 13, 2018, 7:35pm UTC](https://forum.lulzbot.com/t/linear-advance/5488/21 "2018-01-13T19:35:27Z")

</div>

Wonder if with new tool heads, Lulzbot jumps on linear advance band wagon

---

<div class="post-metadata">

**Author:** ![mrvanes](https://sea2.discourse-cdn.com/flex020/user_avatar/forum.lulzbot.com/mrvanes/32/103_2.png) [@mrvanes](https://forum.lulzbot.com/u/mrvanes)\
**Post date:** [January 13, 2018, 8:52pm UTC](https://forum.lulzbot.com/t/linear-advance/5488/22 "2018-01-13T20:52:20Z")

</div>

> [@](#):
>
> Ha… I may end up there. I do have Slic3r PE installed, have tested it a little but haven’t spent the time to really dial it in or create profiles for everything.

Well, you can use mine as a start? Mind that I use bleeding-edge Slic3r builds from [https://dl.slic3r.org/dev/](https://dl.slic3r.org/dev/). Be careful that wipe code could be incompatible with Marlin 1.1.5, I stopped using wipe before print and clean it manually before it descends for probe. And I switched to FWRetract, so “Mini no wipe” printer profile lacks slicer generated retracts settings!  
[Slic3r\_config\_bundle.ini](https://forum.lulzbot.com/uploads/short-url/idRVN5d55lN20RCZmh3aRfmXi2c.ini) (21.7 KB)

---

<div class="post-metadata">

**Author:** ![ScottW](https://avatars.discourse-cdn.com/v4/letter/s/53a042/32.png) [@ScottW](https://forum.lulzbot.com/u/ScottW)\
**Post date:** [January 15, 2018, 3:25am UTC](https://forum.lulzbot.com/t/linear-advance/5488/23 "2018-01-15T03:25:38Z")

</div>

> [@](#):
>
> > [@](#):
> >
> > Ha… I may end up there. I do have Slic3r PE installed, have tested it a little but haven’t spent the time to really dial it in or create profiles for everything.
> 
> Well, you can use mine as a start? Mind that I use bleeding-edge Slic3r builds from [https://dl.slic3r.org/dev/](https://dl.slic3r.org/dev/). Be careful that wipe code could be incompatible with Marlin 1.1.5, I stopped using wipe before print and clean it manually before it descends for probe. And I switched to FWRetract, so “Mini no wipe” printer profile lacks slicer generated retracts settings!

Thank you! I’m busy playing with my new Aerostruder, but adding these profiles and playing with Slic3R just made #2 on my list. 🙂 Really appreciate you taking time to post them.

[Previous page](https://forum.lulzbot.com/t/linear-advance/5488.md?page=1)