Page 3 of 3

Re: Wanted - Taz 6 - Removable flexible bed mod ideas

Posted: Fri Oct 12, 2018 5:08 pm
by BusterCherry
kcchen_00 wrote:
Wed Mar 07, 2018 12:15 am
As for the 5mm PEI, it would be an expensive experiment. A sheet is ~$100. But then again if its not going to be nicked by tools, it becomes less of a consumable. Just need to scoff the surface every so often to reinvigorate the surface.

There is an old thread about testing with the PEI. Some posts cite that the PEI in thicker sheets bow when repeatedly heated, which is concerning. But there are positive posts from people that haven't experienced this. It could simply be laying the PEI down so that it curves into the metal bed, and the corners are secured by the metal fasteners.
Are there sources for 5mm thick PEI sheets? I haven't been able to find a supplier.

Re: Wanted - Taz 6 - Removable flexible bed mod ideas

Posted: Fri Oct 12, 2018 6:27 pm
by kcchen_00

Re: Wanted - Taz 6 - Removable flexible bed mod ideas

Posted: Mon Feb 04, 2019 2:04 pm
by Menissalt
Something like this would be a huge QoL improvement

Re: Wanted - Taz 6 - Removable flexible bed mod ideas

Posted: Mon Feb 04, 2019 9:59 pm
by dysan
I don't think thick pei would be a good choice since pei is more of a thermal insulator than a conductor. When the pei is thin it's not much of an issue when if it is thick then that's an entirely different ball game.

https://www.makeitfrom.com/material-pro ... rimide-PEI

Re: Wanted - Taz 6 - Removable flexible bed mod ideas

Posted: Wed Feb 06, 2019 3:34 pm
by Menissalt
I wish I knew more about metals, magnetism, heat, and where to source the materials. With my BlTouch mod a magnetic flexible bed would be a perfect compliment.

Re: Wanted - Taz 6 - Removable flexible bed mod ideas

Posted: Thu Feb 07, 2019 12:52 am
by kcchen_00
Magnets + Modular heat bed + Buildtak Flexplate w/PEI

Re: Wanted - Taz 6 - Removable flexible bed mod ideas

Posted: Thu Feb 07, 2019 10:54 am
by dysan
I am going to try a heatbed I found on Aliexpress which is a 300watt PCB style with a 3mm aluminum plate and it comes with a spring steel sheet already. The heatbed has magnets under it similar to what the newest Prusa has. Supposedly high temp magnets so it should work at 110c. Long wait time to get it unfortunately.

I'm going to set it up so I can level the bed with screws and at the same time remove the linear rods and go to 2 mgn12H linear rails.

I've switched my Taz 6 over to a Duet Wifi mainboard and I have a BL-Touch on it for mesh bed leveling now.

Here's the link for the heated bed I'm going to try.

https://www.aliexpress.com/item/3D-Prin ... 12466.html

And fyi, Mcmastercarr sells high temperature magnetic sheets you could use that are rated for temps up to 250*F or 121C. The only downside is they are only 9" wide so you would have to piece it together. You can get them 9" x 24" https://www.mcmaster.com/flexible-magnets and scroll down.

Another option for US based magnetic spring steel bed is a the new Wham Bam system which was a kickstarter that is now complete and for sale. You could need a heater though since it just goes on top so you could adhere the magnetic sheet to the existing glass if you remove the PEI and use it that way.

https://whambamsystems.com/