Page 1 of 2

inova 1800, CHROMA STRAND

Posted: Wed Mar 09, 2016 5:10 pm
by claudiacc
Does anyone has printed with inova 1800, i having trouble with the bed, and the flow

Re: inova 1800, CHROMA STRAND

Posted: Wed Mar 09, 2016 5:36 pm
by kmanley57
Sure have! But I use S3D as the guy who makes it does also. But I can share our S3D settings with you if you want to try getting anything out of them. 8-)

There are Inova profiles for Cura available on the development site though.

http://devel.lulzbot.com/print-profiles/cura/

Re: inova 1800, CHROMA STRAND

Posted: Thu Mar 10, 2016 1:12 am
by CoParaTech
For Inova 1800, I set my nozzle temp to 240°, bed to 70°, flow to 90%, filament diameter to 2.85, and z offset to 0.15. Those setting seem to work well on my Mini.

Re: inova 1800, CHROMA STRAND

Posted: Mon Mar 14, 2016 4:19 pm
by claudiacc
Thanks!!!

Re: inova 1800, CHROMA STRAND

Posted: Tue Sep 06, 2016 12:56 pm
by jreynolds
I'm getting a lot of stringiness with this stuff, on our TAZ 5 with .5 nozzle, using Lulzbot Cura 20.01, and starting from the Lulzbot Cura standard high-detail profile . Here's a rocktopus at 50% scale. I've lowered the temperature as low as 235, increased retraction from 4 to 5, lowered the z hop to .075. No real differences except the overall quality when I increased the retraction was poor (the one pictured).
I do have S3D but have no idea where to start with a profile for that. I'm trying to print an iphone lens mount for an ophthalmologist that seems to have pretty close tolerances when assembling the parts, so I thought this would be a good filament choice.
Any suggestions?
Thanks in advance.

Re: inova 1800, CHROMA STRAND

Posted: Tue Sep 06, 2016 1:39 pm
by kmanley57
Here is the one I use for S3D. I have not used it for several months now as I ran out. :oops:
Inova-1800.zip
(3.01 KiB) Downloaded 101 times
20160906_141547.jpg
The Devil made me do it!

Re: inova 1800, CHROMA STRAND

Posted: Tue Sep 06, 2016 3:03 pm
by jreynolds
Thanks! Yeah - it's expensive so I hate to waste it. I'll give this a try.

Re: inova 1800, CHROMA STRAND

Posted: Tue Sep 06, 2016 3:46 pm
by PdxSteve
jreynolds wrote:Thanks! Yeah - it's expensive so I hate to waste it. I'll give this a try.
Bbbbbut it comes in a pretty box!!

Re: inova 1800, CHROMA STRAND

Posted: Fri Sep 09, 2016 8:33 am
by jreynolds
[quote="kmanley57"]Here is the one I use for S3D. I have not used it for several months now as I ran out. :oops:
Inova-1800.zip
Using this S3D profile is an improvement, but it's till seriously stringy. Anyone have any suggestions?

Re: inova 1800, CHROMA STRAND

Posted: Fri Sep 09, 2016 5:01 pm
by kmanley57
I had very little stringing on the little devil I printed above at the time. But I could have altered the profile while making one for the Taz 6 when I got it.

I can try and find the original file I got from the guy whom makes the filament. 8-)