Lightening TAZ 5 Bed

Have questions? Want advice?
Post Reply
discojon
Posts: 432
Joined: Sat Mar 07, 2015 1:54 pm

Lightening TAZ 5 Bed

Post by discojon » Fri Jun 09, 2017 1:21 pm

Now that I have a good grasp on Milling Aluminium with my manual mill and CNC Router, I'm considering removing some mass from the bed. I realize that reducing mass may lead to warping and bending under changing thermal loads but I don't think it will be an issue. Has anyone done this?
TAZ 5, Open rails X,Y,Z. Marlin 1.1 RC2. Mangrove dual fan, reinforced extruder mount

pyrokld
Posts: 58
Joined: Sun Dec 25, 2016 7:57 pm

Re: Lightening TAZ 5 Bed

Post by pyrokld » Fri Jun 09, 2017 9:31 pm

discojon wrote:Now that I have a good grasp on Milling Aluminium with my manual mill and CNC Router, I'm considering removing some mass from the bed. I realize that reducing mass may lead to warping and bending under changing thermal loads but I don't think it will be an issue. Has anyone done this?
I don't have any info on the bed milling, but have you milled any of the dual extruder plates? I've been slowly working on a MPCNC to make my own since I have enough hot ends and fans to put together a duely, just need those custom plates. Itworks3d does sell them but they seem to go out of stock almost instantly, and quite pricy for the lower bracket ($50).
Last edited by pyrokld on Sun Jun 11, 2017 6:46 pm, edited 1 time in total.

User avatar
piercet
Posts: 4027
Joined: Sun Aug 25, 2013 1:37 am
Location: Battleground, WA
Contact:

Re: Lightening TAZ 5 Bed

Post by piercet » Sat Jun 10, 2017 1:46 pm

I'd like to get a 3/16" thick aluminum or copper toolplate made someday, with the back milled out 1/8" with a recess in the shape of the heated bed heater. Keep the edges intact, etc. I've also thought of taking that same kind of plate and adding vacuume channels to the surface to allow a plate to be held on via suction.

discojon
Posts: 432
Joined: Sat Mar 07, 2015 1:54 pm

Re: Lightening TAZ 5 Bed

Post by discojon » Sun Jun 11, 2017 6:09 pm

pyrokld wrote:
discojon wrote:Now that I have a good grasp on Milling Aluminium with my manual mill and CNC Router, I'm considering removing some mass from the bed. I realize that reducing mass may lead to warping and bending under changing thermal loads but I don't think it will be an issue. Has anyone done this?
I don't have any info on the bed milling, but have you milled any of the dual extruder plates? I've been slowly working on a MPCNC to make my own since I have enough hot ends and fans to put together a duely, just need those custom plates. Itworks3d does sell them but they seem to go out of stock almost instantly, and quite pricy for the lower bracket ($50).
I haven't done any dual extruder parts. I'm not a fan of the lulzbot style dual. I can look into making some though.
TAZ 5, Open rails X,Y,Z. Marlin 1.1 RC2. Mangrove dual fan, reinforced extruder mount

discojon
Posts: 432
Joined: Sat Mar 07, 2015 1:54 pm

Re: Lightening TAZ 5 Bed

Post by discojon » Sun Jun 11, 2017 6:10 pm

piercet wrote:I'd like to get a 3/16" thick aluminum or copper toolplate made someday, with the back milled out 1/8" with a recess in the shape of the heated bed heater. Keep the edges intact, etc. I've also thought of taking that same kind of plate and adding vacuume channels to the surface to allow a plate to be held on via suction.
Do you have a dxf of what you are thinking? I can see what i can do.
TAZ 5, Open rails X,Y,Z. Marlin 1.1 RC2. Mangrove dual fan, reinforced extruder mount

User avatar
piercet
Posts: 4027
Joined: Sun Aug 25, 2013 1:37 am
Location: Battleground, WA
Contact:

Re: Lightening TAZ 5 Bed

Post by piercet » Sun Jun 11, 2017 6:24 pm

discojon wrote:
piercet wrote:I'd like to get a 3/16" thick aluminum or copper toolplate made someday, with the back milled out 1/8" with a recess in the shape of the heated bed heater. Keep the edges intact, etc. I've also thought of taking that same kind of plate and adding vacuume channels to the surface to allow a plate to be held on via suction.
Do you have a dxf of what you are thinking? I can see what i can do.

not yet, but I could certanly make one!

Post Reply